background image

Page  12

Maintenance

Microscopy environment

This microscope is recommended to be used in a clean, dry and shock free environment with a temperature of 

5°-40°C and a maximum relative humidity of 75 % (non condensing). Use a dehumidifier if needed.

To think about when and after using the microscope

•   The microscope should always be kept vertically when moving it and be careful so that no

  moving parts, such as the eyepieces, fall out.

•   Never mishandle or impose unnecessary force on the microscope.

•   Never attempt to service the microscope yourself.

•   After use, turn off the light immediately, cover the microscope with the included 

  dust-cover, and keep it in a dry and clean place. 

Electrical safety precautions

•   Before plugging in the power supply, make sure that the supplying voltage of your region  

matches with the operation voltage of the equipment and that the lamp switch is in off- 

position.

•   Users should observe all safety regulations of the region. The equipment has acquired 

  the CE safety label. However, users do have full responsibility to use this equipment safely.

Cleaning the optics

•  If the optical parts need to be cleaned try first to: use compressed air.

•  If that is not sufficient: use a soft lint-free piece of cloth with water and a mild detergent.

•  And as a final option: use the piece of cloth moistened with a 3:7 mixture of ethanol and ether.

  Note: ethanol and ether are highly flammable liquids. Do not use them near a heat source, near sparks or 

near electric equipment. Use these chemicals in a well ventilated room.

•   Remember to never wipe the surface of any optical items with your hands. Fingerprints can damage the 

optics.

•   Do not disassemble objectives or eyepieces in attempt to clean them.

For the best results, use the OPTIKA cleaning kit (see catalogue).

If you need to send the microscope to Optika for maintenance, please use the original packaging.

Summary of Contents for B-500ASB















Reviews: