manualshive.com logo in svg

Optics ODM- 88, User Manual

Share
Download
Optics ODM- 88 User Manual Download Page 71

USER MANUAL 

DVI MATRIX ROUTER : ODM-88 

 

ODM-88 Manual   

Page 71 

 

4.    Troubleshooting 

 

Problem 

Symptom 

Remedy 

Power 

No Power LED 

Check  the  connection  of  power  cord  to  the  ODM-88  and 
AC  power outlet  and that  make sure that power switch is 
in the ON. 

Output 

No Output present 

Check the Input Output DVI cables are firmly connected to 
each  port  of  ODM-88  and  double  check  the  Input  Output 
connection configuration you want. 

The display is not capable of handling graphic resolution. 
Check  the  compatibility  of  EDID  in  the  EEPROM  and 
attached displays. 
When  a  single  Input  is  routed  to  multiple  outputs,  lower 
resolution EDID should be selected.   
EX> Input 1 

 Output 1 (UXGA) & Output 2(SXGA) 

If  EEPROM  1  store  the  display  1  EDID  (UXGA),  the 
display 2 (SXGA) will not work due to resolution limit.   

The source has stopped sending a graphic signal. 
Check that Input source status by connecting it  to availa-
ble monitor without the ODM-88. 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for ODM- 88















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands