manualshive.com logo in svg

Optics ODM- 88, User Manual

Share
Download
Optics ODM- 88 User Manual Download Page 10

USER MANUAL 

DVI MATRIX ROUTER : ODM-88 

 

ODM-88 Manual   

Page 10 

 

 

 

 

 

 

 

 

 

 

Figure 1-3 Concept drawing for setting EDID in ODM-88 

 

As depicted in Figure 1-3, once EDID is configured, each EDID is stored in EEPROM at 
the front of the DVI Input.    As a result, the video sources are able to read EDID from the 
EEPROM during boot-up; even though the ODM-88 and connected displays are not 
powered on yet. 

1.6  Connecting Optical DVI cables and modules for extended distance 

 

ODM-88 supports connection of Optical DVI cables or modules to all inputs and outputs.   
The use of copper DVI cables over 3m (10ft.) is not recommended.   

1.7  Initializing ODM-88 and Installation Guide 

1.7.1 

Initialization 

Plug the provided AC power cord to the AC/DC power adaptor then plug the DC 
cord to the +12VDC connector on the rear panel; make sure that the arrow mark 
on the connector of the DC cord is aligned.   

Push POWER button on the front panel then observe: 

 

Red LED (on the button) 

– will light up 

 

Display 

– will display “ODM-88……….Initializing”   

EEPROM 

EEPROM 

EEPROM 

EEPROM 

EEPROM 

EEPROM 

EEPROM 

EEPROM 

 
 
 
 

 

 

EDID 

INTERFACE 

CONTROL 

 

INPUT 1~8 

OUTPUT 1~8 

WRITE EDID 

Summary of Contents for ODM- 88















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands