The nix sign indicates prohibition.
2
INSTALLATION HINTS
INSTALLATION INSTRUCTIONS
DE
IT
PT
ES
CONSIGNES D'UTILISATION
ISTRUZIONI INSTALLAZIONE
INSTALLATIONSANLEITUNG
INSTRUÇÕES DE INSTALAÇÃO
INSTRUCCIONES DE INSTALACIÓN
FR
EN
* Do not obscure partially or
completely the detector’s
field of view.
3
INSTALLATION
No. 59-2042-3
RXC-RST
RX CORE SERIES
BATTERY OPERATED PASSIVE INFRARED DETECTOR
RXC-RST
BATTERY OPERATED PASSIVE INFRARED DETECTOR
RX CORE SERIES
Warning
Caution
1
PARTS IDENTIFICATION
3-1 WIRELESS TRANSMITTER PREPARATION
Unit: mm (inch)
30 (1.18)
92 (3.62)
44 (1.73)
Connectors to be used
Connector for POWER and ALARM
Connector for TROUBLE
Red
Black
How to position a battery
4
DETECTION ZONE
TOP VIEW
SIDE VIEW
5
10
15
25
30
35
40 ft
6 m
4
2
15
10
5
20 ft
2
4
6
8
10
12 m
4
6 m
0
2
0
5
10
15
20 ft
5
10
15
20
25
30
35
40 ft
0
2.4 m
12 m
10
8
6
4
2
0
8 ft
20
Velcro tape
Screw kit
For wall mounting
Screw (3 × 16 mm) ×3
Lens
Cover
Back Box
Wall tamper
Chassis
3-2 WIRING DIAGRAM
3-3 MOUNTING
1
Remove the cover.
5
SWITCH SETTING
DIP switch
1 WALK TEST MODE
2 LED
3,4 PIR SENSITIVITY
5 ALARM & TROUBLE OUTPUT
DIP switch 1
-WALK TEST MODE
POSITION
FUNCTION
TEST
(Factory default)
NORM
DIP switch 2
-LED
DIP switch 5
-ALARM & TROUBLE OUTPUT
DIP switch 3,4
-PIR SENSITIVITY
NORM
⇔
TEST
ON
1
2
3
4
5
OFF
⇔
ON
N.C.
⇔
N.O.
Once any output is activated, the battery
saving circuit requires 2 minutes of inactivity
before the next output.
The LED lights irrespective of
the DIP switch 2 (LED)
setting.
The LED lights depending on
the DIP switch 2 (LED)
setting.
POSITION
FUNCTION
ON
LED ON
LED OFF
Note>>
If the LED lights, check the
DIP switch 1 (WALK TEST
MODE) setting.
OFF
(Factory default)
POSITION
FUNCTION
(Factory default)
3
4
High sensitivity
Low sensitivity
3
4
3
4
3
4
POSITION
FUNCTION
N.O.
N.O. output
N.C. output
N.C.
(Factory default)
Transmitter side
Main unit side
Red
Black
White
Yellow
Red: Power input (+)
Black: Power input (-)
White: Alarm
Yellow: Alarm
Green: Trouble
Blue: Trouble
Brown: Wall tamper
Orange: Wall tamper
Gray: Wall tamper
Green
Blue
Brown
Orange
Gray
ON
1
2
3
4
5
ON
1
2
3
4
5
ON
1
2
3
4
5
ON
1
2
3
4
5
Installation
Installation
Installazione
Instalação
Instalación
Conseils d'installation
Installations-Tipps
Indicazioni installazione
Dicas de instalação
Recomendaciones de instalación
DE
IT
PT
ES
FR
DE
IT
PT
ES
FR
Zone de détection
Erfassungsbereich
Zone di rilevazione
Zona de detecção
Zona de detección
Reglagles des interrupteur DIP
Schaltereinstellungen
Impostazione dei selettori
Ajuste da chave DIP
Ajuste del conmutador DIP
DE
IT
PT
ES
FR
DE
IT
PT
ES
FR
Identification des pieces
Teilekennzeichnung
Descrizione delle parti
Identificação das partes
Identificación de las partes
DE
IT
PT
ES
FR
Back box
Main unit
Trouble
Wall tamper
Alarm
Wireless
transmitter
Twist
Loosen
Connector for POWER and ALARM
Connector for TROUBLE
3
Separate the chassis from the back box.
ON
1
2
3
4
5
Middle sensitivity
Super High sensitivity
5
Mount the Wireless transmitter to the backbox
or backside of the chassis.
Velcro tape
transmitter
Back box >>
Backside of the chassis >>
Velcro tape
transmitter
4
Mount the back box to the wall.
Note>>
Mounting screws are not included.
Note>>
RXC-RST shall be mounted in a position where
expected intrusion is in perpendicular the
detection patterns.
Corner mounting >>
Backside mounting >>
2
Remove the board.
Push
Pull
Note>>
