If the learning process fails, please remove the Bell Box from the control panel and repeat the step 3-7 again.
Step8.
Slide Dip SW1 on the Bell Box to OFF position. The Bell Box leaves learning mode. If you don’t slide Dip SW1 back to OFF position, the
Bell Box will automatically leave the learning mode one hour after it enters the learning mode.
PROGRAMING THE BELL BOX
Use the Control Panel “
Program Siren
” function to adjust Bellbox settings.
GENERAL SIREN FUNCTION
Changing general siren function will affect the setting of all learned in siren / Bellbox.
SIREN TAMPER
If it is set to “
ON
”, the Bell Box will ativate alarm when the tamper switch is triggered.
If it is set to “
OFF
”, the Bell Box will remain silent when the tamper switch is triggered.
N
N
O
O
T
T
E
E
>
>
>
>
If the siren tamper is set as disabled (
OFF
), it will automatically revert to enable (
ON
) after about an hour if it is not switched back manually.
CONFIRM
If it is set to “
ON
”, the Bell Box will sound beeps when the system is armed or disarmed.
If it is set to “
OFF
”, the Bell Box will remain silent when the system is armed or disarmed.
ENTRY SOUND
If it is set to “
ON
”, the Bell Box will sound beeps when the Entry timer is activated.
If it is set to “
OFF
”, the Bell Box will remain silent when the Entry timer is activated.
9
INSTALLING THE BELL BOX
The tamper switch plunger protrudes through the back of the unit. If the Bell Box is pulled off from the wall, the alarm will be activated. Ensure it is fully
depressed when the Bell Box is mounted. If there is a gap, pack with a suitable spacing material.
Step1.
Find the location where the Bell Box is to be mounted.
Step2.
Using the large screws and wall plugs provided, mount on wall through the 4 x mounting holes.
Step3.
Fix the Bell Box cover with the securing screw.
Step4.
Enable tamper switch by selecting the tamper enable/disable menu on the Control Panel (please refer to the
Manual of Control Panel for details).
Step5.
Check if the installation is successful by arming and disarming the Control Panel.
N
N
O
O
T
T
E
E
>
>
>
>
If 5 short-beeps are noticed while arming, it means the tamper is not correctly set. Check to ensure that tamper is
properly set and then test from Control Panel again.
Step6.
The installation is now completed.
10 CHANGING THE BATTERY
Step1.
Find the Control Panel’s Program Siren menu and disable the Siren Tamper function. The Bell Box will emit a beep when the tamper is
disabled.
Step2.
Release the screws at the bottom of the Bell Box and pull the outer case out carefully.
Step3.
The battery compartment is a large box in the Bell Box with a lid secured with 4 screws.
Step4.
Remove the four screws and take off the compartment lid.
Step5.
Remove the old batteries and press the Tamper Switch twice to discharge.
Step6.
Insert the new D cell alkaline batteries into the battery compartment. Orient the batteries according to the correct polarity.
Step7.
The Bell Box will emit beeps and flash when the last battery is inserted.
Step8.
Replace the battery compartment lid with the four screws taking care not to over tighten.
Step9.
Enable the Siren Tamper funciton in Control Panel menu. The Bell Box will sound a beep to indicate the tamper protection is now
activated.
11 SPECIFICATIONS
Model
GEN-OSR
Frequency
433.82 MHz
Power source
D size alkaline battery: 4 units
Battery life
Approx. 2.5 years (1 activations per year, 25°C)
Operating conditions
-10°C to +55°C (up to 85% non-condensing)
Weight
1300 g (including battery)
12 DIMENSIONS
202
71
2
87
Unit: mm
