www.openplan.com | [email protected] | 844.OPS.OPS1 | REV 07.01.2020
4
4
Step 5: Replace the standard Bottom Draw Block with the Bottom Guide Assembly (L or R) by releasing the Top Draw Block at the top of the panel.
Position the Guide Bracket under the Sliding Door, behind the front caster.
Step 6: Check positioning, alignment, and level of the Sliding Door, ensuring the frame is not resting on the Guide Bracket . Adjust the
panel height to lower or raise the guide. To level the door, or provide additional height adjustment, loosen the lock nut and turn in/turn
out the caster stem. Tighten the Lock nut when desired caster height is set. Check the overall door position by extending and closing
the door. There should be a smooth roll and minimal obstruction when rolling the door in or out.
Door should not sit
directly on Bottom
Guide. Leave about
1/8” spacing.
Loosen/tighten the
Locknut and thread
the caster in/out to
adjust overall door
height (Also to level
door).
Loosen Draw
Block Bolt.
Replace standard
Bottom Draw Block with
Guide Block and re-
tighten Draw Bolt.
ASSEMBLY GUIDE
Step 5
Replace the standard Bottom Draw Block with the Bottom Guide Assembly (L or R) by releasing the Top Draw Block at the top of the panel. Position
the Guide Bracket under the Sliding Door, behind the front caster.
Loosen Draw
Block Bolt
Replace standard Bottom
Draw Block with Guide Block
and re-tighten Draw Bolt.
Step 6
Check positioning, alignment, and level of the Sliding Door, ensuring the frame is not resting on the Guide Bracket . Adjust the panel height to lower
or raise the guide. To level the door, or provide additional height adjustment, loosen the lock nut and turn in/turn out the caster stem. Tighten the
Lock nut when desired caster height is set. Check the overall door position by extending and closing the door. There should be a smooth roll and
minimal obstruction when rolling the door in or out.
Door should not sit directly on
Bottom Guide. Leave about 1/8”
spacing.
Loosen/tighten the Locknut and
thread the caster in/out to adjust
overall door height (Also to level
door).
4
Step 5: Replace the standard Bottom Draw Block with the Bottom Guide Assembly (L or R) by releasing the Top Draw Block at the top of the panel.
Position the Guide Bracket under the Sliding Door, behind the front caster.
Step 6: Check positioning, alignment, and level of the Sliding Door, ensuring the frame is not resting on the Guide Bracket . Adjust the
panel height to lower or raise the guide. To level the door, or provide additional height adjustment, loosen the lock nut and turn in/turn
out the caster stem. Tighten the Lock nut when desired caster height is set. Check the overall door position by extending and closing
the door. There should be a smooth roll and minimal obstruction when rolling the door in or out.
Door should not sit
directly on Bottom
Guide. Leave about
1/8” spacing.
Loosen/tighten the
Locknut and thread
the caster in/out to
adjust overall door
height (Also to level
door).
Loosen Draw
Block Bolt.
Replace standard
Bottom Draw Block with
Guide Block and re-
tighten Draw Bolt.
4
Step 5: Replace the standard Bottom Draw Block with the Bottom Guide Assembly (L or R) by releasing the Top Draw Block at the top of the panel.
Position the Guide Bracket under the Sliding Door, behind the front caster.
Step 6: Check positioning, alignment, and level of the Sliding Door, ensuring the frame is not resting on the Guide Bracket . Adjust the
panel height to lower or raise the guide. To level the door, or provide additional height adjustment, loosen the lock nut and turn in/turn
out the caster stem. Tighten the Lock nut when desired caster height is set. Check the overall door position by extending and closing
the door. There should be a smooth roll and minimal obstruction when rolling the door in or out.
Door should not sit
directly on Bottom
Guide. Leave about
1/8” spacing.
Loosen/tighten the
Locknut and thread
the caster in/out to
adjust overall door
height (Also to level
door).
Loosen Draw
Block Bolt.
Replace standard
Bottom Draw Block with
Guide Block and re-
tighten Draw Bolt.
4
Step 5: Replace the standard Bottom Draw Block with the Bottom Guide Assembly (L or R) by releasing the Top Draw Block at the top of the panel.
Position the Guide Bracket under the Sliding Door, behind the front caster.
Step 6: Check positioning, alignment, and level of the Sliding Door, ensuring the frame is not resting on the Guide Bracket . Adjust the
panel height to lower or raise the guide. To level the door, or provide additional height adjustment, loosen the lock nut and turn in/turn
out the caster stem. Tighten the Lock nut when desired caster height is set. Check the overall door position by extending and closing
the door. There should be a smooth roll and minimal obstruction when rolling the door in or out.
Door should not sit
directly on Bottom
Guide. Leave about
1/8” spacing.
Loosen/tighten the
Locknut and thread
the caster in/out to
adjust overall door
height (Also to level
door).
Loosen Draw
Block Bolt.
Replace standard
Bottom Draw Block with
Guide Block and re-
tighten Draw Bolt.
4
Step 5: Replace the standard Bottom Draw Block with the Bottom Guide Assembly (L or R) by releasing the Top Draw Block at the top of the panel.
Position the Guide Bracket under the Sliding Door, behind the front caster.
Step 6: Check positioning, alignment, and level of the Sliding Door, ensuring the frame is not resting on the Guide Bracket . Adjust the
panel height to lower or raise the guide. To level the door, or provide additional height adjustment, loosen the lock nut and turn in/turn
out the caster stem. Tighten the Lock nut when desired caster height is set. Check the overall door position by extending and closing
the door. There should be a smooth roll and minimal obstruction when rolling the door in or out.
Door should not sit
directly on Bottom
Guide. Leave about
1/8” spacing.
Loosen/tighten the
Locknut and thread
the caster in/out to
adjust overall door
height (Also to level
door).
Loosen Draw
Block Bolt.
Replace standard
Bottom Draw Block with
Guide Block and re-
tighten Draw Bolt.
