8
2.5 Organizational measures
The workstation frame can best be assembled by two people. Turning the frame, once the work
surface has been fitted, is a task in particular which requires two people!
2.6 Informal safety measures
Keep the assembly/operating manual in the place where the workstation frame is used at all
times.
Make sure that all safety information on the table (see Section 2.2, Symbols used on the work-
station frame) is legible, replacing the same if necessary.
2.7 Note for those assembling the workstation
The workstation must be assembled/worked on by persons over the age of 16.
The persons referred to above must have read and understood the assembly /operating manu-
al.
2.8 Transport and assembly
The workstation frame must be moved by two persons only, and in such cases must be retract-
ed.
Do not drag or pull the workstation frame over the floor.
Assemble the workstation frame with the supplied tools only. They are the only tools which en-
sure that the screws can be tightened to the correct torque.
2.9 Use of the workstation frame
Do not allow children to use the workstation frame unsupervised. Children may be unaware of
the dangers presented by the workstation frame. They would be in serious danger of injuring
themselves, possibly even with fatal consequences. Further adjustment must then be impossible
as a safeguard against use by children.
The workstation frame must only be used in appropriate areas.
Do not use the workstation frame on an uneven surface. In such conditions it will not be steady.
Never exceed the maximum load on the workstation frame.
2.10 Specific dangers
When adjusting the height of the frame there is danger of injury. Make sure that there is no-one
else in the immediate surroundings of the frame.
When assembling the workstation frame, make sure there is ample space to avoid collisions (i.e.
inclination of roof, fixed objects, filing cabinets, waste-paper bins etc.) in all imaginable direc-
tions.
Make sure there is ample space to avoid collisions if there are objects on the work surface such
as computers or computer peripherals.
Make sure there is clearance of at least 25 mm from all other furniture, all around the workstation
frame.
2.11 In an emergency
Stop using the workstation frame at once if you notice anything unusual (strange sounds etc.).
Have the workstation frame repaired by specialists. Refrain from using the workstation frame until
it has been successfully repaired.
2.12 Maintenance and upkeep
The workstation frame and its components are low-maintenance items and need no special
regular maintenance.
Do not perform any repairs on the work surface or other components yourself.
Do not alter the construction of the work surface or its frame.
Any faulty components removed must be replaced with new, original components from the
manufacturer. Use only original replacement parts made by the manufacturer. Have any such
work carried out by a specialist, making reference to this Assembly/operating manual.
English
Summary of Contents for STEELFORCE PRO 570 SLS
