Quick Start Guide
700-0129-203
1
3
5
2
4
6
8
Package Contents
Introduction
The Ooma Safety Phone is a small speaker phone
that can be worn or kept by your side all day.
Since the Safety Phone is a fully-working speaker
phone capable of two-way communication, you can
use it to make and receive calls anywhere within the
range of your home Ooma system.
Comfortable to wear and programmable with up to
two speed dial numbers, the Safety Phone gives
you the peace of mind that your caretaker and loved
ones are just a button press away. The Safety Phone
can effectively support your independent lifestyle.
Important Information About the Safety Phone
•
Carefully read and follow the instructions in this
Quick Start Guide, which may also be viewed
online at:
http://www.ooma.com/support/documentation
Do not use the Safety Phone if you cannot
understand and follow the instructions.
•
Use of the Safety Phone requires high-speed
Internet access and the Ooma Telo device. The
Safety Phone will not work if either the Internet or
Ooma Telo are not functioning properly.
•
The Safety Phone is intended for indoor use with a
range of up to 50 meters (164 feet) from the Ooma
Telo. This range may vary based on factors such
as home construction and other electrical devices
and appliances being used in the home.
•
The battery in the Safety Phone is not replaceable.
The expected lifetime of the battery is two years,
but may vary based on usage.
•
Do not use the Safety Phone if you have an
implanted cardiac pacemaker.
Charging cradle with
AC
adapter
Microphone
Status LED
Changes color and blinks
to indicate the status of
the Safety Phone.
Talk
Press to place a call, and
again to end the call.
Press and hold to power the
Safety Phone on or off.
Speaker
Volume Up
Press to increase earpiece
or ringer volume.
Volume Down
Press to decrease earpiece
or ringer volume.
Speed Dial Buttons
Charge Phone
Register Phone
Program Speed Dial Online
Quick Reference Guide
Place the Safety Phone on the charging cradle
and charge for a few minutes until the status
LED turns purple and you start to hear the Safety
Phone play two short beeps periodically.
When you are ready to register the phone, take
it out of the cradle and put it back in. The status
LED will start to blink red and blue.
Press and hold the PAGE button on your Ooma
device for three seconds to activate registration
mode.
The Safety Phone will now register with your
Ooma system. When the registration process
is successful, you will hear a long beep.
Continue to charge the Safety Phone for at
least three hours until the status LED lights up
solid blue.
Front
Back
Finish the installation process by going to:
http://my.ooma.com/devices
Here you will be able to program the two
speed dial buttons.
Step 1
Step 2
Step 3
Ooma Safety Phone with lanyard
BC
Breakway
connector
WARNING:
To avoid injury,
please review the Important Safety
Information section on page 11
before using the Safety Phone.
Operation Instructions
•
Powering the Safety Phone on or off
To power the phone on or off, press and hold the
TALK button until you hear three short beeps.
•
Making an outgoing call
Outgoing calls can be placed to either of the two
pre-programmed speed dial buttons. Press the
appropriate button to call the programmed number.
•
Answering a call
Answer incoming calls by pressing the TALK button.
•
Ending a call
To end a call, press the TALK button again while
on a call. You can also end a call by putting the
Safety Phone back onto the charging cradle.
•
Adjusting the volume
The speaker volume can be adjusted up by pressing
the VOLUME UP or VOLUME DOWN button during
a call. Use the same buttons to adjust the ringer
volume when the phone is in idle mode.
•
Registering to a new base unit
Register the Safety Phone to a different base unit
by pressing and holding the VOLUME UP and
VOLUME DOWN buttons at the same time until the
status LED toggles between red and blue.
7
