Onkyo TX-NR801E, Service Manual

Page: 3 / 117

TX-NR801/E
SERVICE PROCEDURES
1. Replacing the fuses
This symbol located near the fuses indicates
that the fuse used is fast operating type. For continued
protection against fire hazard, replace with same type fuse.
For fuse rating refer to the marking adjacent to the symbol.
Ce symbole indique que le fusible utlise est a
rapide. Pour une protection permanente, n'untiliser que
fusibles de meme type. Ce darnier est la qu le present
symbol est appse.
Note: <D>: 120V model only
<O>: Except 120V model
<T>: Worldwide model only
<R>: Chinese model only
CIRCUIT NO.
PART NO. DESCRIPTION
F901 252199 10A-UL,Fuse <D/T/R>
F902 252077, 4A-SE-EAK,
252243 or 4A-SE-TL250V or
252277 4A-SE-TL250V <O>
F903 252164 or 5A-UL/T-237 or
252258 5A-T/UL-ST2,Fuse <D>
252075, 2.5A-SE-EAK,
252241 or 2.5A-SE-TL250V or
252275
2.5A-SE-TL250V,Fuse <O>
F9501,F9502 252160 or
2.5A-UL/T-237 or
252254 2.5A-T/UL-ST2,Fuse <D>
252075, 2.5A-SE-EAK,
252241 or 2.5A-SE-TL250V or
252275 2.5A-SE-TL250V,Fuse <O>
F9503,F9504 252158 or 1.6A-UL/T-237 or
252252
1.6A-T/UL-ST2,Fuse <D>
252073,
1.6A-SE-EAK,
252239 or 1.6A-SE-TL250V or
252273 1.6A-SE-TL250V,Fuse <O>
2. To initialize the unit
This device employs a microprocessor to perform various
functions and operations. If interference generated by an
external power supply, radio wave, or other electrical source
results in accident which causes the specified operations
and functions to operate abnormally.
To perform a result, please follow the procedure below.
1.Press the STANDBY ON button to turn on the unit.
2.Press and hold down the VIDEO 1 button, then press the
STANDBY/ON button.
3.After "CLEAR" is displayed, the preset memory and each
mode stored in the memory, such as surround, are
initialized and will return to the factory setting.
4.Unplug the power supply cord.
4. Memory Preservation
This unit does not require memory preservation batteries. A
built-in memory power back-up system preserves the contents
of the memory during power failures and even when the unit is
unplugged. The unit must be plugged in order to charge the
back-up system.
The memory preserv ation period after the unit has been
unplugged varies depending on climate and placement of the
unit. On the average, memory contents are protected over a
period of a fe w weeks after the last time the unit has been
unplugged.
This period is shorter when the unit is exposed to a
highly humid climate.
5.Setting the voltage selector
(Worldwide models only)
Worldwide models are equipped with a voltage selector so
that you
supplies. Be
can set your TX-NR801 to conform with local power
sure to set this switch to match the voltage of
your area before plugging in the unit.
Determine the proper voltage for your area: 220-230 V or
the preset voltage is not correct for your area,
into the groove in the switch and slide
(220-230 V), whichever is appropriate.
the power supply in
120 V. If
insert a screwdriver
the switch all the way to the top (120 V) or bottom
3. Safety-check out
(U.S.A. model only)
After correcting the original service problem, perform the
following safety check before releasing the set to the customer.
Leakage Current Check
Measure leakage current to a known earth ground(water pipe,
conduit, etc.) by connecting a leakage current tester between
the earth ground and exposed metal parts of the appliance
(input/output terminals, screwheads,metal overlays, etc.).
Plug the power supply cord directly into a 120V AC 60 Hz outlet
and turn Standby switch on. Any current meausred must not
exceed 0.5mA.
SURR
BACK/
ZONE 2
SPEAKERS
AUDIO VIDEO S VIDEO
MONITOR
OUT
R L
IN
IN
IN
IN
IN
ZONE 2
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
AUDIO VIDEO S VIDEO
COMPONENT
VIDEO
Y
PB
PR
OUTPUT
INPUT 1
Y
PB
PR
INPUT 2
Y
PB
PR
FRONT SPEAKERS
L R L R
SURR SPEAKERS
CENTER
SPEAKER
R L
R L
OUT
OUT
OUT
I R
IN
OUT
REMOTE
CONTROL
PHONO
DIGITAL
IN
PRE OUT
DIGITAL
OUT
OPT
OPT
2
1
2
1
2
3
FRONT
SUB
SURR
R L
AUDIO
R L
CD
TAPE
R L
AUDIO
1
3
GND
SURR
BACK/
ZONE 2
IN
OUT
COAX
R L
MULTI CH
INPUT FRONT
SUB
SURR
SURR
BACK
CENTER
R L
R L
AM
FM
75
CENTER
ANTENNA
IN
IN
( Net-Tune )
ETHERNET
4 OHMS MIN. OR
6 OHMS MIN.
/SPEAKER
CAUTION:
SPEAKER
IMPEDANCE
SEE INSTRUCTION
MANUAL FOR
CORRECT SETTINGS.
AV RECEIVER
MODEL NO. TX-NR 801
VOLTAGE
SELECTOR
220-230V
120V
AC OUTLETS
AC 230-240 V 50 Hz
SWITCHED
TOTAL 100 W MAX.
120V
VOLTAGE
SELECTOR
220-230V
6.AM Frequenc y Step Sub-menu
orldwide model Only)
This sub-menu only appears on the worldwide model.
The setting in this sub-menu determines the incremental
or decremental amount when adjusting the AM tuner
frequenc y.
The initial setting is 9 kHz, and this needs
only to be changed if you are using the TX-NR801/
TX-NR801E in a 10 kHz region.
a. Frequency Step
9 kHz: Select when you use the TX-NR801/
TX-NR801E in North America.
10 kHz: Select when you use the TX-NR801/
TX-NR801E in other than USA and Canada.
0-5.AM Frequency Step
a.Frequency Step
:9 kHz
Quit:[SETUP]
3