Onkyo HT-R960, Service Manual

Page: 83 / 191

TX-SR606
FIRMWARE UPDATE-3
UPDATE OF DSP
REMOTE
CONTROL
COAXIAL
OPTICAL
1
(DVD)
2
(CBL/SAT)
1
(GAME/TV)
2
(CD)
DIGITAL IN
ASSIGNABLE
IN 1(DVD) IN 2
COMPONENT VIDEO
Y
CB/PB
CR/PR
ASSIGNABLE
HDMI
IN 1 IN 2 IN 3 IN 4
ASSIGNABLE
R
L
IN IN IN
IN
IN
IN
IN
IN IN
CBL/SAT GAME/TV
GAME/TV CBL/SAT
VCR/DVR
VCR/DVR
TAPE CD
DVD
S
V
OUT
(DVD) (GAME/TV) (CBL/SAT) (VCR/DVR)
OUT
OUT
OUT
OUT
L
R
DIGITAL
ANALOG
REMOTE
CONTROL OUT
OUT
OPTICAL
OPTICAL
1
(VCR/DVR)
DIGITAL
OUT
OPTICAL
Target unit
Rear panel
CD player
D S P S R 6 0 6 : 0 8 6 1 1 A
W r i t i n g . . .
S / P D I F U p d a t e . .
D i g i n : A U T O
M a i n 1 . 0 3 / 0 8 6 3 0 A
C l e a r
Standby mode
*Number depends on the version.
*Number depends on the version.
Preparation for update
Update is done by playback of CD-R in a CD player.
Tool
1 . Blank CD-R : 1pc, PC (Personal computer with CD-R writer)
2 . Writing soft : “CD_SR6060_08213A.wav” (File name depends on the version.)
<Note>
Store it in a blank CD-R as a music CD in advance. For a writing soft, contact Onkyo or your local distributor.
3 . CD player with Optical or Coaxial output terminal.
<Note>
Some CD players and a lot of DVD players process audio signal before output. Such players cannot be used for this update.
4 . Optical cable or Coaxial cable : 1pc.
Connection and setup
1 . Connect a CD Player with the target unit via Optical Input 1 or Coaxial Input 1.
2 . Power on the unit and wait for more than 10 seconds.
Update Procedure
1 . Press and hold down DISPLAY DISPLAY button and then press ON/STANDBY ON/STANDBY button to show Main microprocessor FW version
when the unit is powered on.
2 . Press +(TONE) +(TONE) button twice while the Main microprocessor FW version is displayed for about 3 seconds.
Then, DSP FW version will be displayed.
3 . Press RETURN RETURN button while the DSP version is displayed. Then, the following message will appear.
4 . Press ENTER ENTER button. Then, the following message will appear.
5 . Play the DSP FW CD-R with the CD player. After playback finished, writing will start.
<Note1>
If the above message does not appear after waiting for a while, please try again.
Some DVD players are not suitable for this update. If writing results in failure, use another model of player.
<Note2>
DURING WRITING, DO NOT TURN OFF THE POWER and DO NOT DISCONNECT OPTICAL/COAXIAL CABLE.
If writing is stopped in the middle, Flash IC may need replacing.
6 . After writing ends, the message on Front Display will change as follows.
7 . Confirm the new version number. refer to “FIRMWARE UPDATE-1”.
www. xiaoyu163. com
QQ 376315150
9 9
2
8 9
4 2
9 8
TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com