Onicon Vortex Flow Meter F-2200 Series Installation And Operation Manual Download Page 14 | Manualshive

Page: 14 / 22

Onicon Vortex Flow Meter F-2200 Series Installation And Operation Manual Download Page 14

F-2200 Series Vortex Flow Meter Installation and Operation Guide • Revised 12/08

15

3.2 MECHANICAL

INSTALLATION

3.2.1 Orient The Display For Convenient Viewing

Both the electronics enclosure and the display itself can be rotated to four different

orientations to change the viewing angle for the display. If necessary, this should be done

before the meter is installed.

3.2.1.1 Rotating the electronics enclosure

The electronics enclosure is attached to the meter body with (4) 5mm Allen head

screws. To rotate the enclosure, you must fi rst remove the screws and then carefully

rotate the enclosure as needed. The interconnecting stem assembly is a conduit for

wires that connect the sensors to the circuitry contained in the enclosure. Care must

be taken to prevent these wires from being damaged when rotating the enclosure.

!

CAUTION

Make certain the sensor wires are not damaged when re-attaching the enclosure.

«
...
12
13
14
15
16
...
»

Summary of Contents for Vortex Flow Meter F-2200 Series























Reviews:

No comments