manualshive.com logo in svg

Onicon F-5000, Installation And Operation Manual, Page: 8 / 28

Share
Download
Onicon F-5000 Installation And Operation Manual Download Page 8

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 10/16 - 2032 / 107050 

Page  8

COM Port Assignment

Be sure to have your F-5000 series flow meter connected by mini USB to a PC or 
laptop before opening the F-5000 View software. Upon opening F-5000 View for the 
first time, Windows will assign a "virtual COM port".  The COM port number that has 
been assigned will appear automatically in the drop down box.  
If the correct COM Port does not appear, go to Control Panel/Device Manager and click 
on Ports (COM & LPT).  The COM port number should be displayed under the USB 
symbol.

If prompted, enter the assigned COM port in F-5000 View by using the drop down 
menu and press 

OK

.

Note: The flow meter must be plugged into the computer in order for the system to 
register it.

Fig. 2.3: COM Port Selection Window

i

Operation: Main Screen

Main Screen

F-5000 View

OPERA

TION

Installation

COM Port 

Assignment

Summary of Contents for F-5000





























Reviews:

No comments