manualshive.com logo in svg

Onicon F-4600 Series, Installation And Operation Manual

Share
Download
Onicon F-4600 Series Installation And Operation Manual Download Page 7

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 

Page 

7

1.4   WORKING ENVIRONMENT

The F-4600 with optional LCD display was designed for installation and use indoors or outdoors 
in protected spaces, or in residential, commercial and light industrial environments that are free 
of corrosive liquids and fumes, temperature extremes and excess vibration. 

The operating ambient air temperature range is -13°F to 131°F. The electrical power should be 
relatively clean, free of excess high frequency noise and large voltage transients.

1.5   SERIAL NUMBER

Serial Number

The serial number of your F-4600 is located on the side of the enclosure. The serial number 
is a unique identifier for the product. Please have this number available when contacting 
ONICON for assistance.

SECTION 2.0:  UNPACKING

The F-4600 is generally shipped in one package unless optional hardware or equipment is ordered. 
Notify the freight carrier and ONICON if any items are damaged in transit. 

2.1  CHECKING THAT YOU HAVE RECEIVED EVERYTHING

The following items have been provided with your F-4600 Flow Meter:

Two line size process connection meter couplings* with male NPT threads and sealing gaskets 

(shipped attached to meter)

One F-4600 Meter Installation and Operation Guide
One F-4600 Meter Certificate of Calibration
One Remote Mount Bracket

Please notify ONICON if any of these items are missing.

*NOTE: The 2

½

” version of the meter is provided with flanges.

Summary of Contents for F-4600 Series






































Reviews:

No comments

Brands by name

Popular brands

Load more brands