Oneida Air Systems Super Dust Gorilla 2hp Owner'S Manual Download Page 3

Page: 3 / 19

I. System Start-Up Information

O.A.S. 2002

2HP Commercial Wood Dust Collector Owners Manual

1. Read the installation and maintenance instructions as well as the recommended

safety practices in this manual.
2. Install Ductwork completely before operating collector:

A.) Seal ductwork with silicone sealant or duct tape.

B.) Have Dust Bin in place and sealed.

3. Have licensed electrician wire Fan / Blower according to wire diagram on pg. 14

in this owners manual.
4. Have licensed electrician check current draw on motor with all gates open. Current

draw should not exceed maximum motor amperage. (OAS is not responsible for

damage to motors caused by improper installation, wiring or failure to follow these

directions.)

Caution

The Direct Drive Fan / Blower makes the system top heavy!

Use extreme care when setting the unit up!

Warning

If amperage is too high - shut down immediately!

(See troubleshooting section.)

Warning

Do not operate Fan / Blower unless Cyclone and Dust Bin

are in place. Motor will over heat!

Warning

Check amperage draw during operation with all blast gates

open. Make certain amperage is not outside operating limit

indicated on motor plate!

Summary of Contents for Super Dust Gorilla 2hp




















Search results

Summary of Contents for Super Dust Gorilla 2hp

Reviews:

Related manuals for Super Dust Gorilla 2hp

Brands by name

Popular brands

Oneida Air Systems Super Dust Gorilla 2hp, Owner'S Manual

Search results

Summary of Contents for Super Dust Gorilla 2hp

Reviews:

Related manuals for Super Dust Gorilla 2hp

Brands by name

Popular brands