background image

                                                                                     

 

It includes 3 items:Active , Passive and Response mode   

Active

: Reader keep reading card, and transmit each of card number by communication 

port (apply to active upload data).   

Passive

: Reader keep reading card, and each of card number store in reader, but do not 

upload card number,the max. storage is 100pcs (apply to passive upload). 3.   

Response: 

Reader do not read card, reader response according difference commands. 

For example, PC send a recognize card command, reader will read a time and reply card 

number to PC (apply to short distance read and write card, test).   

 

Output Mode:

   

It includes RS232, TCPIP, CANBUS, Wiegand26 and Wiegand34.   

RS232:

 Serial port communication mode, It connects with PC serial port directly and point 

to point mode.    

TCPIP

 

  Network communication mode, it communicate with PC by LAN or WAN. 

CANBUS

 

  BUS communication mode, it is point to multiple mode.   

Wiegand26

 

  It is standard reader communication mode, one-way communication mode. 

Wiegand34 

  It  is  standard  reader  communication  mode,  one-way  communication 

mode. 

 

Read Interval

:The speed of reading card.   

 

Note: read card interval must more than 10ms. If read card interval is too short, it will short 

lift of the reader.

 

 

Power Size

: The max. value is 30.   

 

Trigger:

   

1. 

Close:

 Close trigger mode to read card.   

2. 

Low Trigger:

 When trigger lead (gray wire) connect with low power (OV), reader power 

on, when trigger lead (gray wire) connect with high power (12V), reader power off.   

 

Note:  When  Trigger  mode  is  Close,  trigger  lead  must  connect  with  high  power  or  low 

power and can not be dangling. 

 

Same ID Interval

  When  reader  read  a  same  card  continuously,  reader  only  upload  one  data.  The  read 

interval  can  be  set  at  here,  and  if  the  read  time  is  over  set  interval,  reader  will  upload 

continuously. Buzzer: When reader read card, the buzzer beep or not. 

 

Buzzer:   

It includes disable and enable, disable mean turn off the buzzer, when read card, no beep, 

enable mean turn on the buzzer, when read card, with beep. 

Summary of Contents for 2E-2656





















Reviews: