One for All URC7125 Quick Start Manual Download Page 6

Page: 6 / 8

LEARNING

Your One For All remote control can learn any function from any other working remote control.

This can be useful if you are missing one or more functions from your original remote control and

would like to add them to the ONE FOR ALL. You can learn onto any key except MAGIC or MODE.

You can also learn a complete device if you can’t find a code.

To learn, firstly make sure you have all your original remote controls to hand, and that they have

working batteries in. To learn functions, the original remote should be approximately 3cm from

the OFA remote, pointing towards it as shown below:

Hold down MAGIC until the LED under the device blinks twice.

The LED under the current device will stay lit.

Press the MODE key repeatedly until the LED for the device you want to

learn functions on is lit.

Press 975 – the LED will blink twice.

Press and release the key you want to learn a function onto (for example

the HOME key) – The red LED will blink continuously.

Press and release the key on the original remote.

The LED will blink twice to indicate the key has been learned correctly.

Repeat steps 4 and 5 for each key you want to learn – remember you can learn from multiple

remotes, but only one function per key.

When you learned all the functions you require, press and hold the

MAGIC key until the LED blinks twice and turns off.

HINTS

•

If the LEDs shows one long blink at step 6, the function was not learned correctly, please try

again from step 4.

•

If you find one or more keys don’t work properly after set up, you can re-enter the learning

mode at any time by repeating the procedure from step 1.

TO DELETE A LEARNED FUNCTION, THE PROCEDURE IS:

Hold down MAGIC until the LED under the device blinks twice.

The LED under the current device will stay lit.

Using the MODE key, make sure the LED for the device you want to delete functions

from is lit.

Press 976 – the LED will blink twice

Press the key to delete twice – the LED will blink twice.

Repeat the above procedure for each key you want to delete.

ACTIVITIES

The Watch TV feature combines TV and STB into a single mode. In this mode the Volume and AV

keys will control the TV, and the rest of the keys will control the STB.

As the AV key is intended to select the input on your TV and most TVs use a menu to select from a

list of inputs, when the AV key is pressed in Watch TV Mode, the Menu Up, Down, Left, Right and

OK keys temporarily control the TV. If the OK key is pressed, or no key is pressed for ten seconds,

these keys will revert to controlling the STB.

If you hold down the Power key for 2 seconds in Watch TV Mode, the remote will send the Power

function for TV and STB.

MACROS

PROGRAM A MACRO

You can program any key on your OFA remote (except MAGIC or MODE) to send multiple

commands on a single press –a Macro. This can be useful for controlling multiple devices to put

them in a certain state – for instance you could put your TV on HDMI 1 and press Power on the

Set Top Box to start watching TV.

To program a macro, the procedure is as follows:

Hold down MAGIC until the LED under the device blinks twice.

The LED under the current device will stay lit.

Press 995 – the LED will blink twice.

Next select the key you want to program the Macro on.

Now use the MODE key to select the device you want the first function

of the Macro to come from, for example TV.

Next, press the key you want to include in the Macro, for example the

AV key.

Repeat steps 4 (if necessary) and 5 to add more keys to the Macro. You can include up to 15

key presses .

To store the Macro, hold down the MAGIC key until the LED blinks twice.

•

If the LED shows a long blink when you press a key in steps 4 or 5, you have entered too

many keys, please try again.

DELETING A MACRO

If you want to remove a macro from a key, please perform the following:

Hold down MAGIC until the LED under the device blinks twice. The LED

under the current device will stay lit.

Press 995 – the LED will blink twice.

Press the key the macro is programmed on.

Now hold down the MAGIC key until the LED blinks twice – the Macro is

deleted.

VOLUME LOCK

If you always use one device to control volume, for example your TV, you can set up the One For

All to always control that device, regardless of which device your remote is controlling. To do this:

Hold down MAGIC until the LED under the device blinks twice. The LED under the current

device will stay lit.

Press 993 – the LED will blink twice.

Use the MODE key to select the Device you want to lock the Volume to.

Press MAGIC once – the LED will blink twice and volume is now locked.

To unlock the volume and set every device back to controlling its own volume, the procedure is:

Hold down MAGIC until the LED under the TV key blinks twice. The LED under the current

mode key will stay lit.

Press 993 – the LED will blink twice.

Press VOLUME UP – the LED will blink twice and Volume is now unlocked.

2 - 5 CM

THE NETTV FEATURE

The Evolve features a “NETTV” key for viewing digital TV,

streamed over the internet. If your original remote control

already had a key for this - for example many newer TVs have

a Netflix key - then this key will perform exactly the same as

the key on your original remote. However if you did not have

a key like this, but still had the ability to watch a streaming

service, you can use this key as a shortcut by programming a

macro on it. Most AV devices which are connected to the internet, such as Smart TVs or streaming

Set Top Boxes have one or more applications they can run to access TV viewing via the internet.

Examples of these would be Netflix, YouTube, Amazon Prime, BBC iPlayer or similar.

To program the macro, you first need to know the device you use to access the service, and then

the sequence of keys you need to press to always bring up the service you prefer, For example,

some Panasonic TVs will start Netflix by pressing the Apps key, then Menu Down Twice, and

finally the OK key. Or on an Apple TV, the sequence is Menu, Menu Down and OK.

Once you have determined the sequence for your device, follow these steps:

Sit in front of your device with It switched on (not on standby)

Hold down the NETTV key until the LED blinks twice and stays lit

Use the MODE key to select the device you want to use for the NETTV macro (e.g. TV)

Now perform the sequence of keys exactly as would normally. The remote will operate your

device and the macro is recorded in real time - so if it normally takes a few seconds for your

device to react don’t worry.

One you have finished the sequence - and the Streaming Service has started on your device -

hold down the NETTV key until the LED blinks twice and goes out. The macro is now stored.

Tips

•

Make sure the Evolve Is operating the device in question before programming

If you find the Macro doesn’t work as expected, you can just repeat the same sequence

to reprogram

•

When programming, wait for your device to respond first, the remote will remember

the timing

•

The NETTV macro is tied to one device, remember to make sure you are watching

the correct device.

English - PRODUCT DISPOSAL (EUROPEAN DIRECTIVE 2012/19/EU)

The crossed out wheeled bin symbol on this product ensures that this product is manufactured
using high quality components that can be recycled and reused according European Directive
2012/19/EU. Please do not dispose of this product with your normal household waste, refer to local
regulations for the proper collection or disposal of electrical and electronic products. This will help
this will help in preventing negative effects on the environment and/or human health.

BATTERY DISPOSAL (EUROPEAN DIRECTIVE 2006/66/EC)Please do not dispose of your batteries with your
normal household waste, refer to local regulations for the proper collection or disposal. This will help
preventing potential negative effects on the environment and/or human health.

GUARANTEE TERMS AND CONDITIONS UNIVERSAL ELECTRONICS warrants to the original purchaser that this
product will be free from defects in materials and workmanship under normal and correct use for a period of
two (2) years from the date of original purchase. This product will be repaired or if necessary, replaced free of
charge if it has been proven to be defective within the two(2) year warranty period. The forwarding costs are
on the account of the owner; the costs of returning the product are on the account of UNIVERSAL
ELECTRONICS.

This warranty does not cover damage or failures caused by products or services not supplied by UNIVERSAL
ELECTRONICS, or which result from not mounting the product according to manual instructions. This also
applies when the product has been modified / repaired by others than UNIVERSAL ELECTRONICS or if a fault
is the result of accident, misuse, abuse, neglect, mishandling, misapplication, faulty installation, improper
maintenance, alteration, modifications, fire, water, lightning, natural disasters, wrong use or carelessness.

To obtain warranty service during the warranty period contact […], and please note that we need your
original purchase receipt so that we may establish your eligibility for service. If you have bought this product
for purposes which are not related to your trade, business or profession, you may have legal rights under your
national legislation governing the sale of consumer goods. This guarantee does not affect those rights.
www.oneforall.com