INSTRUCTION / INSTALLATION SHEET
ev
ō
Q™ 5000 Angled In-Ceiling Speaker
IS-0384 Rev. O
301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone (800) 321-2343 / Fax (717) 702-2546
www.onqlegrand.com
©Copyright 2007 by On-Q/Legrand All Rights Reserved.
Page 3 of 3
B. “Trim-out”
steps:
1. After drywall and/or painting is complete, push the speaker wire
through hole, center template over hole, mark with a pencil and cut
out with a dry-wall knife.
2.
Hold the speaker with one hand, (if speaker grill is off, pay careful
attention
not
to push on the woofer’s cone, this can cause
permanent contortion of the voice coil, thus producing a
mechanical rubbing sound or speaker failure), push in the speaker
terminal connectors and insert wires; remove speaker grill. Be
sure to have the positive wires in the RED terminals and the
negative wires in the BLACK terminals.
NOTE: Wiring both drivers of this speaker identically as the
above instruction states will yield a speaker whose drivers are
“in phase”. If one speaker driver is wired opposite of the
other, the speaker drivers will be “out of phase” with one
another. If the speaker drivers are “out of phase” the sound
might appear smeared (canned) and a significant loss of bass
might be noticeable due to phase cancellation. Make sure
every installed speaker is correctly phased.
3. Rotate the speaker driver towards the listening area and use
one hand to push the speaker into the cut out (again, pay
careful attention
not
to push on the woofer’s cone, this can
cause permanent contortion of the voice coil, thus producing
mechanical rubbing sound or speaker failure) and the other to
turn the screws that engage the installation tabs (see
Figure
5
). Tighten the tabs in a cross or X-pattern until “snug”. Be
careful not to over tighten the tabs or damage could result. The
speaker should appear flush to the surface.
NOTE: If using a cordless drill/screwdriver, it is suggested
that the screws be turned until almost tight, then finish
tightening via a hand screwdriver.
NOTE: A strip of grill adhesive is provided to more securely attach the speaker grills on final
installation. Simply insert several short strips evenly around the grill slot prior to installing the
grill cover. Prior to final installation of the grill, adjust the tweeter for optimum sound at the
listening area.
6.5" Speaker (0.7 CuFt)
Blocking Distance
16" on Center, 2x4
24.00"
16" on Center, 2x6
15.25"
16" on Center, 2x8
11.50"
16" on Center, 2x10
9.00"
16" on Center, 2x12
7.50"
24" on Center, 2x4
15.50"
24" on Center, 2x6
10.00"
8" Speaker (2.1 CuFt)
Blocking Distance
16" on Center, 2x4
71.50"
16" on Center, 2x6
45.50"
16" on Center, 2x8
34.50"
16" on Center, 2x10
27.00"
16" on Center, 2x12
22.25"
24" on Center, 2x4
46.00"
24" on Center, 2x6
29.50"
ev
ō
Q™ Speaker Blocking
Chart
Figure 5
ev
ō
Q™ 5000 ANGLED IN-
CEILING SPEAKER
Size/Type 6.5"
In-Ceiling
Efficiency 90dB
Power (RMS/Peak)
75W/150W
Frequency
Response
60-20K
Woofer Type
Poly
Tweeter Type
UFLC Adjustable
Drywall Hole Size
9.5” dia.
Speaker
Specifications
