manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 240

Setting Measurement Items

238

ZW-8000/7000/5000 

User's Manual

Measuring the Thickness

Measuring the Thickness p.140

As an example, here is an explanation of the procedure for measuring the thickness from the top surface of 

glass on which specular reflection occurs as the 1st surface to the 2nd surface (as shown in the diagram on 

p.140). 

Operating procedure

Steps

Key operation

Display

Description

1

Press and hold the 

 key for two seconds or more to enter the 

FUNC mode.
To save the setting, refer to "7-3 Functions of Operating Keys" 
(p.222).

2

Set the material of the target to “MIRROR.”  

 Setting the Material of the Target to Measure p.230

If the target object is a transparent object, such as glass, on which specular reflection occurs, set the material of the 
measurement object to “MIRROR” to obtain more accurate measurement result. 

3

Set the surface to “SUR.1ST.” 

3-1

Press the 

/

 key to select MEAS, then press the 

 key.

3-2

Press the 

/

 key to select TASK1, then press the 

 key.

3-3

Press the 

/

 keys to select “ITEM” and press the 

 key. 

3-4

Press the 

/

 keys to select “THICK” and press the 

 key. 

3-5

Select “SUR1.”
Press the 

/

 keys to select “TOP” and press the 

 key. 

3-6

Select the measurement surface. 

EDGE1 to EDGE4: 1st surface to 4th surface
PEAK: Peak

The current setting value is displayed on the sub-display.

Press 

/

 key to enter editing mode and the sub-display blinks.

In this example, select “EDGE1” and press the 

 key. 

4

Set the surface2 to “SUR.2ND.”

Optional

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands