manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 142

Setting Measurement Items

140

ZW-8000/7000/5000 

User's Manual

Measuring the Thickness

If you have glass of known thickness, scaling can be adjusted referenced to that glass so that transparent 

objects can be measured more easily.

 Multi View Explorer

: [Bank Group] | [(Bank Data Name)] (double click)

 

→

 Edit pane

: [Task Settings] icon (

)

 

→

 Task Settings window : [Measurement mode]

• When the measurement surface setting is set to Peak for thickness measurement, the measurement may become 

unstable depending on the incident level on each surface. Change the measurement surface setting for each 

surface from Peak to 1/2/3/4.

• With the above procedure, the same area surface must be set for Measurement surface 1 and Measurement 

surface 2. Therefore, to set different area surfaces for Measurement surface 1 and Measurement surface 2, set the 

height measurement of each surface to two tasks and calculate the difference.

Item

Setting item

Setting value

Description

Thickness 
settings

Measurement 
surface 1

Edge1/Edge2/Edge3/Edge4/

 

Peak (default value)

The measurement surface (top surface) targeted for 
measurement can be switched.
The peak is the surface of all measurement surfaces having 
the highest received light amount.

Measurement 
surface 2

Edge1/Edge2 /Edge3/Edge4/

 

Peak (default value)

The measurement surface (rear surface) targeted for 
measurement can be switched.
The peak is the surface of all measurement surfaces having 
the highest received light amount.

1

Select [Thickness] in [Measurement mode].

2

Select the measurement surface (top 

surface) targeted for measurement from 

[Measurement surface 1].

3

Select the measurement surface (rear 

surface) targeted for measurement from 

[Measurement surface 2].

Sensor head

Transparent 
object

Edge 1st

Edge 2nd

Thickness

Important

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands