manualshive.com logo in svg

Omron S8VS - MODEL 15-30-60-90-120-180-240W, Manual, Page: 19 / 28

Share
Download
Omron S8VS - MODEL 15-30-60-90-120-180-240W Manual Download Page 19

Switch Mode Power Supply

 S8VS

19

Dimensions

Note:

All units are in millimeters unless otherwise indicated.

Note:

The illustration is the S8VS-03024 Model.

Note:

The illustration is the S8VS-06024A Model.

Note:

The illustration is the S8VS-12024A Model.

Note:

The illustration is the S8VS-18024A Model.

S8VS-015

@@

 (15-W)

S8VS-030

@@

 (30-W)

4.8
(Sliding: 10 max.)

4.8
(Sliding: 10 max.)

35.2

96.4

22.5

4

85

97

11.3

35.4

108.3

1

40

10

74

95

Five, M4 
with square washer

Track stopper

4.5

(Sliding: 15 max.)

S8VS-06024 (60-W)
S8VS-06024

@

 (60-W)

110.5

10.8

34.9

121.3

1

94

115

10

50

Five, M4 
with square washer

Track stopper

Screwless block (2.5 mm pitches)

4.5

(Sliding: 15 max.)

S8VS-09024 (90-W)/S8VS-12024 (120-W)
S8VS-09024

@@

 (90-W)/S8VS-12024

@@

 (120-W)

94

115

10

75

4.5

125.3

120.3

34.9

S8VS-18024 (180-W)
S8VS-18024

@@

 (180-W)

Summary of Contents for S8VS - MODEL 15-30-60-90-120-180-240W





























Reviews:

No comments