manualshive.com logo in svg

Omron S8VS - MODEL 15-30-60-90-120-180-240W, Manual, Page: 10 / 28

Share
Download
Omron S8VS - MODEL 15-30-60-90-120-180-240W Manual Download Page 10

10

Switch Mode Power Supply

 

S8VS

Construction and Nomenclature

 (60-W, 90-W, 120-W, 180-W, and 240-W Models)

■

Nomenclature

Note: 1.

The fuse is located on the (L) side. It is NOT user-replace-
able.

2.

This is the protective earth terminal specified in the safety
standards. Always ground this terminal. 

3.

S8VS-

@@@

24

@@

 only.

4.

S8VS-

@@@

24

@@

 only (excluding S8VS-06024

@

).

5.

Both sinking and sourcing outputs are available. 

6.

S8VS-

@@@

24A

@

 only (excluding S8VS-06024A).

7.

S8VS-

@@@

24B

@

 only (excluding S8VS-06024B).

60-W Models

Standard Model

Models with Display Monitor

S8VS-06024

S8VS-06024

@

Note:

The S8VS-06024A is shown 
above.

90-W/120-W Models

Standard Models

Models with Display Monitor

S8VS-09024/S8VS-12024

S8VS-09024

@@

/S8VS-12024

@@

Note:

The S8VS-12024A is shown
above.

180-W Models

Standard Model

Models with Display Monitor

S8VS-18024

S8VS-18024

@@

Note:

The S8VS-18024A is shown
above.

240-W Models

Standard Model

Models with Display Monitor

S8VS-24024

S8VS-24024

@@

Note:

The S8VS-24024A is shown
above.

1

3

2

4

5

1

3

2

4

8

7

6

5

3

1

2

4

5

3

1

13

12

11

2

4

5

8

9

7

6

10

3

1

2

3

4

5

1

2

3

4

5

1113

6

10

12

7

8

9

4

5

3

1

2

13

11

4

5

8

9

7

12

6

10

3

1

2

No.

Name

Function

1

AC Input terminals 
(L), (N)

Connect the input lines to these 
terminals. (See note 1.)

2

Protective Earth 
terminal (PE) 

Connect the ground line to this 
terminal. (See note 2.)

3

DC Output terminals 
(

−

V), (+V)

Connect the load lines to these 
terminals.

4

Output indicator 
(DC ON: Green)

Lights while a direct current (DC) 
output is ON.

5

Output voltage 
adjuster (V.ADJ)

Use to adjust the voltage.

6

Main display (Red) 
(See note 3.)

Indicates the measurement or set 
value.

7

Operation 
indicator (Orange)
(See note 3.)

V

Lights up when the output voltage is 
indicated. Blinks during setup of 
undervoltage alarm value.

A

Lights up during indication of output 
current.

Apk

Lights up during indication of peak 
hold current.

Yrs

Lights up during indication of 
maintenance forecast monitor. Blinks 
during setup of maintenance forecast 
monitor setting. (S8VS-

@@@

24A

@

)

kh

Lights up during indication of total run 
time monitor. Blinks during setup of 
total run time monitor. (S8VS-

@@@

24B

@

)

8

Mode Key (See note 3.) Use the Mode Key to change the 

indicated parameter or reset the peak 
hold current value.

9

Up Key (See note 4.)

Use the Up Key to change to the 
setting mode or to increase the set 
value.

10

Down Key (See note 4.) Use the Down Key to change to the 

setting mode or to decrease the set 
value.

11

Alarm 
outputs 
(See 
notes 4 
and 5.)

Undervoltage 
output terminal 
(DC Low)

Output when a drop is detected in the 
output voltage (voltage drop = 
transistor OFF).

12

Maintenance 
Forecast 
output terminal 
(Yrs)
(See note 6.)

Output when the set value for 
maintenance is reached (transistor 
OFF). 

Total run time 
output terminal 
(kh) (See note 
7.)

Output when the set value for total 
run time is reached (transistor OFF).

13

Common 
terminal

Common terminal (emitter) for 
terminals 11 and 12. 

Summary of Contents for S8VS - MODEL 15-30-60-90-120-180-240W





























Reviews:

No comments