Omron S8VM Series Product Manual Download

Page: 4 / 36

Switch Mode Power Supply

S8VM

Note: 1. Do not use the Inverter output for the Power Supply. Inverters with an output frequency of 50/60 Hz are available, but the rise in the internal temperature of

the Power Supply may result in ignition or burning.

2. Refer to the Engineering Data section on page 15 to 17 for details.
3. If the V. ADJ adjuster is turned, the voltage will increase by more than +20% of the voltage adjustment range. When adjusting the output voltage, confirm the

actual output voltage from the Power Supply and be sure that the load is not damaged.

4. To reset the protection, turn OFF the input power for three minutes or longer and then turn it back ON. Alternatively, turn OFF the remote control signal and

then turn it back ON again.

5. Conducted emissions: The noise value is affected by factors such as the wiring method. The Power Supply conforms to Class B when the aluminum plate

is laid under the Power Supply. For 600-W models, insert a clamp filter (ZCAT3035-1330 by TDK: 100

Ω

min. [50 to 500 MHz], or the equivalent) in the input

wire, and ring core (HF60T38X14X22 by TDK: 16

Ω

typ. [1 MHz], 46

Ω

typ. [10 MHz] , or the equivalent) in the output wire to reduce noise

6. Radiated emissions: The noise value is affected by factors such as the wiring method. The Power Supply conforms to Class A when the aluminum plate is

laid under the Power Supply (1,500-W models).

7. The measuring method conforms to JEITA standard RC-9131A. Refer to Ripple under Safety Precautions on page 34.
8. The Power Supply will not conform to safety standards if the customer replaces the fan.

Item

Power rating

300 W

600 W

1,500 W

Efficiency

5-V models

77% min.

---

12-V models

78% min.

79% min.

---

15-V models

79% min.

80% min.

---

24-V models

81% min.

82% min.

Input

Voltage (See note 1.)

100 to 240 VAC (85 to 264 VAC)

100 to 240 VAC (85 to 265 VAC)

Frequency (See note 1.)

50/60 Hz (47 to 63 Hz)

Current

100-V input

4.0 A max. (5 V)
4.3 A max. (12 V, 15 V, and 24 V)

8.0 A max. (5 V)
8.3 A max. (12 V, 15 V, and 24 V)

20.0 A max.

200-V input

2.0 A max. (5 V)
2.2 A max. (12 V, 15 V, and 24 V)

4.0 A max. (5 V)
4.2 A max. (12 V, 15 V, and 24 V)

11.0 A max.

Power factor

100-V input

0.98 min.

0.97 min.

200-V input

0.94 min.

0.93 min.

Harmonic current emissions

Conforms to EN61000-3-2

Leakage current

100-V input

0.4 mA max.

1.5 mA max.

200-V input

0.75 mA max.

1.5 mA max.

Inrush current
(See note 2.)

100-V input

20 A max. (for cold start at 25

200-V input

40 A max. (for cold start at 25

Output

Voltage adjustment range (See note 3.)

−

20% to 20% (with V. ADJ)

Ripple

3.8% (p-p) max. (5 V), 2.0% (p-p) max. (12 V), 2.0% (p-p) max. (15 V),
1.25% (p-p) max. (24 V), (at rated input/output voltage)

1.25% (p-p) max. (See note 7.),
(at rated input/output voltage)

Input variation influence

0.4% max. (at 85 to 264 VAC input, 100%)

Load variation influence (rated input voltage)

0.6% max. (with rated input, 0 to 100% load)

Temperature variation influence

0.02%/

C max.

Start up time (See note 2.)

1,000 ms max. (at rated input/output voltage)

Hold time (See note 2.)

20 ms typ. (15 ms min.) (at rated input/output voltage)

Additional
functions

Overload protection (See note 2.)

105% to 160% of rated load current (5 V, 12 V, and 15 V), 120% to 160% of rated
load current (S8VM-30024C), 115% to 160% of rated load current (S8VM-
60024C), voltage drop (12 V, 15 V, and 24 V), voltage drop, intermittent (5 V),
automatic reset

105% to 160% of rated load current (100 VAC),
155% to 200% of rated load current (200 VAC),
voltage drop, automatic reset (Turns OFF
when continuous for 5 s min.) (See note 4.)

Overvoltage protection (See note 2.)

Yes (See note 4.)

Overheat protection (See note 2.)

Yes (See note 4.)

Undervoltage alarm indication

Undervoltage alarm output

Power failure alarm indication

Yes (color: red)

Power failure alarm output

Yes (Transistor output), 30 VDC max., 50 mA max.

Series operation

Yes

Parallel operation

Yes (Up to 2 units)

Remote sensing function

Yes

Remote control function

Yes

Other

Ambient operating temperature

Refer to the derating curve in Engineering Data (300-W, 600-W, 1,500-W Models). (with no icing or condensation) (See note 2.)

Storage temperature

−

25 to 65

Ambient operating humidity

30% to 85% (Storage humidity: 25% to 90%)

Dielectric strength

3.0 kVAC for 1 min. (between all inputs and outputs; detection current: 20 mA)
2.0 kVAC for 1 min. (between all inputs and PE terminals; detection current: 20
mA)
500 VAC for 1 min. (between all outputs and PE terminals; detection current: 100
mA)
100 VAC for 1 min. (between all outputs and RC terminals; detection current: 100
mA)
500 VAC for 1 min. (between all outputs and PF terminals; detection current: 20
mA)

3.0 kVAC for 1 min. (between all inputs and
outputs; detection current: 20 mA)
2.0 kVAC for 1 min. (between all inputs and FG
terminals; detection current: 20 mA)
500 VAC for 1 min. (between all outputs and
FG terminals; detection current: 300 mA)
100 VAC for 1 min. (between all outputs and
RC terminals; detection current: 100 mA)
500 VAC for 1 min. (between all outputs and
PF terminals; detection current: 20 mA)

Insulation resistance

100 M

Ω

min. (between all outputs and all inputs, PE terminals) at 500 VDC

100 M

Ω

min. (between all outputs and all in-

puts, FG terminals) at 500 VDC

Vibration resistance

10 to 55 Hz, 0.375-mm single amplitude for 2 hours each in X, Y, and Z directions 10 to 55 Hz, 0.15-mm single amplitude for 2

hours each in X, Y, and Z directions

Shock resistance