background image

S8VK-R

10

Mounting

The long-term reliability of the S8VK-R can be increased by installing 
it properly and sufficiently considering heat dissipation.
Install the S8VK-R so that the air flow circulates around it, because 
the S8VK-R is designed to radiate heat by means of natural air 
circulation.
Can be used in a contact mounting with the S8VK-G (not covered by 
safety certification). Two S8VK-G units cannot be mounted together 
in a contact mounting.

Input Voltage

Rating
S8VK-R10: DC5 to 30V
S8VK-R20: DC10 to 60V

Input Power Supply Selection

This product contains an internal fuse. If a power supply other than 
the S8VK-G is used, the fuse may blow, depending on the state of the 
load. Do not connect a power supply other than the S8VK-G to this 
product.
If you are building a redundant system, never use in a state that 
exceeds the rated current of the power supply. If one of the power 
supplies goes down, there is a risk that the voltage on the load side 
cannot be attained.
Use the same model for the power supplies that are connected. 
On rare occasions internal element deterioration and damage may 
occur if use is continued in a short-circuit or over-current state. Do not 
continue use for more than 10 seconds.
Do not use in applications where load rush current or overload may 
frequently occur. Slight risk of deterioration and damage due to 
internal loss.
The signal output / status LED may occasionally not operate stably.
When using in environments where the temperature is less than 

25 

°

C, always adjust the 5 V power supply to 5.3 V or higher.

Dielectric Strength Test

The S8VK-R is designed to withstand a voltage test of 1 kV AC 
between all input/output terminals and the chassis, and 0.5 kV AC 
between all input/output terminals and the signal output terminal, for 
one minute.

Note:
1. 
The S8VK-R may possibly be damaged from the impulse voltage 

if a testing device switch is used to abruptly apply or shut off 1 kV 
AC, 0.5 kV AC. Increase the applied voltage gradually using the 
voltage adjustment on the testing device.

2. When testing, always short-circuit all terminals to prevent damage 

to the output terminal.

Signal output

Photo switch output
Photo switch ON when input voltage difference is 2.4 V typ. or less.
30 VDC max. (LVLC), 50 mA max., residual voltage when ON: 2 V 
max., leakage current when OFF: 0.1 mA max.

Status display LEDs

The status display LEDs show the status of the input power as shown 
in the table below.
Redundancy OK

Green on: Input voltage difference is 2.4 V typ. or less.

Voltage balance

Green on: Input voltage difference is 50 mV typ. or less.

The redundancy OK display/signal operates when the voltage 
difference is no more than 2.4 V typ. When using a 5 V or 12 V power 
supply, verify that there is no difference in the output voltages of the 
power supplies.
The voltage balance display does not guarantee current balance. The 
degree of balance varies by model, and therefore if you require 
operation with balanced current, check the output current of each 
power supply unit.
The models below use a voltage balance display, and cannot be used 
as a current balance.
S8VK-G015

@@

S8VK-G03012

·

S8VK-G03024

S8VK-G06024
When adjusting the voltage based on the voltage balance, adjust the 
voltage of only one power supply. If you must adjust the voltages of 
both power supplies, be sure to check the output voltage before use.
If you want to use the voltage balance display to ensure that the 
expected life is obtained, use the same thickness and length of wiring 
from each S8VK-G to the S8VK-R.

Connections

It is possible to connect S8VK-R like below.

Precautions for Correct Use

*

1. Convection of air

*

2. 75 mm min.

*

3. 75 mm min.

*

4. 20 mm min.

*

1

*

2

*

1

*

4

*

4

*

3

IN1

OUT

IN2

REDUNDANCY

UNIT

POWER SUPPLY

L N

POWER SUPPLY

L N

REDUNDANCY

MONITOR

LOAD

L

N

OPTIONAL

FG

Summary of Contents for S8VK-R Series













Reviews: