Omron S8JX-G Series, Installation Instructions Manual, Page: 55 / 61

S 8 JX
55
S8JX-G
S8JX-P
Common Precautions
Safety Precautions
Refer to Safety Precautions for All Power Supplies .
Minor electric shock, fire, or Product failure may
occasionally occur. Do not disassemble, modify, or
repair the Product to touch the interior of the
Product.
Minor burns may occasionally occur. Do not touch
the Product while power is being supplied or
immediately after power is turned OFF.
Fire may occasionally occur. Tighten terminal screws
to the specified torque.
M3.5, M4:1.13 N·m.
(The DC output terminal of S 8 JX-G15005
@@ and
S8JX-P15005
:1.56 N·m.)
M5:2.25 N·m.
Minor injury due to electric shock may occasionally
occur. Do not touch the terminals while power is
being supplied. Always close the terminal cover after
wiring.
Minor electric shock, fire, or Product failure may
occasionally occur. Do not allow any pieces of metal
or conductors or any clippings or cuttings resulting
from installation work to enter the Product.
Mounting
•
Take adequate measures to ensure proper heat dissipation to
increase the long-term reliability of the Product.
•
The 300 W 24V, 48V models of S8JX-G series are designed to
radiate heat by means of natural air-flow. Be sure to allow
convection in the atmosphere around devices when mounting. Do
not use in locations where the ambient temperature exceeds the
range of the derating curve.
•
The 300 W 5V, 12V, 600 W models of S8JX-G series, and 300 W,
600 W models of S8JX-P series are designed to radiate heat by
means of forced air-flow. Do not cover the air holes (provided at fan
mounted side and the opposite side) to have enough air-cooling.
•
The screws must not protrude beyond the following values inside
the Power Supply when screw holes provided on the chassis are
used.
15 W, 35 W, 50 W, 100 W, or 150 W: 4 mm
300 W or 600 W of S8JX-P series: 6 mm
300 W or 600 W of S8JX-G series: 8 mm
Mounting screw tightening torque (recommended value) : 0.54 N
· m.
•
Front mounting is possible using provided mounting bracket.
•
When cutting out holes for mounting, make sure that cuttings do
not enter the interior of the Products.
•
Improper mounting will interfere with heat dissipation and may
occasionally result in deterioration or damage of internal parts. Use
the standard mounting method only.
•
The internal parts may occasionally deteriorate and be broken due
to adverse heat radiation. Do not loosen the screw on the side face
of the main body.
•
When mounting two or more Power Supplies side-by-side, allow at
least 20 mm for S8JX-G series and 15 mm for S8JX-P series
spacing between them.
•
Provide a space of at least 20 mm back and forth for S8JX-G
series, and 50 mm back and forth for S8JX-P series when
mounting 300-W and 600-W models as well.
•
Use the metal plate as the mounting panel.
•
Minor fire may occasionally occur. Set the input voltage switch to
the input voltage that is to be used (150-W, 5-V models of S8JX-G
series only).
*1.
Convection of air
*2.
20 mm min. (15 mm min. for S8JX-P series)
*3.
Use a metal plate as the mounting surface.
CAUTION
Precautions for Safe Use
15-/35-/50-/100-/150-W Models
S 8 JX-G Series 300-W 5V, 12V Model
S 8 JX-G Series 300-W 24V, 4 8 V Model
Standard Mo u nting
(Horizontal Mo u nting)
*
1
*
1
*
2
*
3
Standard Mo u nting
(Bottom-mo u nting)
*
1
*
1
*
2
*
3
*
1
*
2
*
1
Standard Mo u nting
(Front-mo u nting and DI N Rail-mo u nting)
*
1
*
1
*
1
*
3
*
2
*
2
Standard Mo u nting
(Bottom-mo u nting)
Standard Mo u nting
(Front-mo u nting and DI N Rail-mo u nting)