background image

 

 

 

Unit Operations:

 

 
The work bits I0200.00 to I0200.15 control the mode of operation of the unit as follows: 

 
Work Bit 

       Function 

 

 

I0200.00   

 

Controls 

LED0 

             

 

 

 

 

 

 

 

 

 

   

 

I0200.01      Controls 

LED1  

I0200.02 &   
I0200.03      Not 

used 

I0200.04 to   
I0200.07 

 

    Reserved for future use 

I0200.08 &   

    00 : Screen mode 

01 : Register mode 

I0200.09 

 

    10 : Operator mode  11 : Invalid   

I0200.10 &   

    Timeout to screen mode from Operator mode 

I0200.11 

  

    00 : 10 seconds  

01 : 20 seconds 

 

 

 

  

    10 : 30 seconds    

11 : 40 seconds  

I0200.12 to   
I0200.14 

 

    Reserved for future use 

I0200.15 

 

    To disable data entry in Screen mode 

     

 

(ON 

Disable) 

 
From the above table, it is clear that the unit will display ASCII text (see section on 

Screens

 for 

more details on this ) if I0200.08 and I0200.09 are OFF.  To allow operators to view and edit the 
registers, I0200.09 is to be kept ON.  If I0200.09 is OFF, the unit will not display any registers and 
the function keys will only act as push buttons mapped to the corresponding bits from I0201.00.  
Refer to “Register Mode” for details.  If I0200.09 is ON, REG key press will allow an operator to 
view the registers.  The REG key will scroll through the available register types whereas the UP 
and DOWN arrow keys will scroll through the register/bit numbers. After timeout specified by bits 
10 and 11 and if no key is pressed, the unit will switch back to the Screen mode and display 
screens.  Thus Operator mode is a combination of Register as well as Screen modes.  

 

 

 

Summary of Contents for NT2S-SF123B-E -











Reviews: