background image

H5L

7

Example

ON and OFF Programs
Cyclic Programs

In this example, the first circuit is programmed to turn ON at 7:40 and OFF at 19:30. This circuit is operated from Monday through Friday and 
stopped on Saturday and Sunday.
The second circuit is cyclically operated with each parameter set as follows:
Start time:

6:50

ON time:

5 min

OFF time:

20 min

Stop time:

20:30

The second circuit is stopped from operating on Sunday and operated from Monday through Saturday. The current time is assumed to be 11:15 
a.m. on Tuesday.

Writing Program

Even while being programmed, the timer generates output according to the previous program. If you don’t want an unexpected operation of output 
relay, turn on (or off) the manual switch.
In the figure, the indicators and digits shown in are blinking.

1. Setting Current Time

Set the current hour to 11 by pressing the Plus or Minus Key, followed by the Write Key.

This completes the current time setting.

To set the current time, "day of the week", "hour", and "minute" must be specified.
First, turn on the power to the H5L.
The contents of the memory are cleared on power-up and the TIM ADJ indicator is displayed as 
shown on the left.As an example, set the time to 11:15 on Tuesday.

Start by setting the day of the week. The blinking indicator indicates the parameter that can be set. 
Set the current day of the week to Tuesday by pressing the Plus or Minus Key.

When "TUE" is displayed, press the Write Key to store the current day of the week in memory. The 
"hour" indicator will begin to flash and the  day of the week" indicator will stop flashing.

At this time, the "minute" indicator will blink. Set the current minute to 15 by pressing the Plus or 
Minus Key, followed by the Write Key.

Summary of Contents for H5L Series















Reviews: