Omron GigE Vision STC-CMB2MPOE Product Specifications And User'S Manual Download Page 54

Page: 54 / 55

No.13S064-13

54/55

STC-CMC2MPOE / STC-CMB2MPOE / STC-CMB2MPOE-IR /
STC-CMC4MPOE / STC-CMB4MPOE / STC-CMB4MPOE-IR Product Specifications and User’s Guide

10 Revision History

Rev

Date

Changes

Note

2013/10/21



New Document

・

Combined Specification and User’s Guide

2013/10/31



Revised

・

Added Technical Note

2013/11/19



Revised

・

Added Pixel Blemish Correction

2013/12/27



Revised

・

LED information on RJ45

2014/10/17



Revised

・

Added TriggerOverlap on GenIcam

2015/01/15

2015/03/10



Revised

・

Company name

・

The minimum number of lines is 4 lines and the maximum frame rate is 4000 fps

・

The serial number is added at DeviceID

・

The camera inside temperature (unit: deg. C) can be measure with
DeviceTemperature in GenICam

・

TriggerSelector function is added. FrameStart or AcquisitionStart is selectable.

・

SoftwareOrHardware is added at TriggerSource selection in GenICam

・

DigitalGain setting range is changed to “1x to 5x (setting: 0 to 511)

・

ExposureTime (Gain, BlackLeve), ExposureTimeRaw
(GainRaw, BlackLevelRaw), ExposureTimeAbs (GainAbs, BlackLevelAbs) in
GenICam are supported

・

Off for ExposureMode is added

The selection for ExposureMode is Off/Timed/TriggerWidth

・

Deleted 12bit output description on38H

2015/09/16



Revised

・

Minimum exposure time 24usec

2016/03/14



Revised

・

Camera Mount Screws

2016/08/26



Revised

・

Dimensions (Added screw lock holes)

2016/010/18



Revised

・

Deleted description of DC IRIS

2017/07/03



Revised

Change the name of company

2018/09/04



Revised

Change the electronic specifications list (Image output format)
Change sensor information (Bayer)

2019/02/27



Revised

Added trademark information

GigE Vision is trademark of AIA.
GenICam is trademark of EMVA.
Other company names and product names in this document are trademarks of their respective owners.

Summary of Contents for GigE Vision STC-CMB2MPOE
























































Search results

Summary of Contents for GigE Vision STC-CMB2MPOE

Reviews:

Related manuals for GigE Vision STC-CMB2MPOE

Brands by name

Popular brands

Omron GigE Vision STC-CMB2MPOE, Product Specifications And User'S Manual

Search results

Summary of Contents for GigE Vision STC-CMB2MPOE

Reviews:

Related manuals for GigE Vision STC-CMB2MPOE

Brands by name

Popular brands