●
Meanings of Signal Words
●
Alert statements
■
Dimensions
■
Accessories
■
General specifications
■
When changing camera direction
■
Performance specifications
INSTRUCTION SHEET
Item
Picture element
Shutter speed
Effective pixels
Pixel size
Scanning method
Vertical frequency
Horizontal frequency
Pixel frequency
Number of lines to be read
Synchronization
Video output
Gain
Operating system
Camera specif
ications
Lens
Illumination
14.4 W maximum. (12 VDC, 1.2 A maximum)
150 m/s
2
, 3 times each in 6 directions
Operating and storage : 35 to 85 %
(with no condensation)
10 to 150 Hz, half-amplitude : 0.35 mm
(maximum acceleration 50 m/s
2
)
10 times for 8 minutes each in 3 directions
Operating : 0 to 50 °C (with no icing or condensation)
Storage : -25 to 60 °C (with no icing or condensation)
No corrosive gases
Cover for camera : Galvanized steel sheet metal
Case for camera : Aluminum alloy
Case for lens : ABS
Cover for illumination: Aluminum alloy
Mount base : Aluminum alloy
Approx. 670 g (including base).
INTELLIGENT CAMERA FOR FZ VSIAUAL INSPECTION SYSTEM
Model
FZ-SLC100
PRECAUTIONS ON SAFETY
· Do not use the product in environments where it may be exposed to
inflammable gas.
· Tighten all screws securely during installation.
2. Other Precautions
· D
o not use unspecified camera cable and a strobe controller other than
those that specified in this manual with the FZ controller. Connection with
unspecified camera cable and/or strobe controller may cause temperature
rise and malfunctions at the worst case.
· Do not attempt to disassemble, repair, or modify the Camera.
· If you notice any abnormality in the Camera, stop using it immediately, turn
OFF the power supply, and contact your OMRON sales representative.
· When disposing of the Camera, dispose of it as industrial waste.
Observe the following precautions to prevent the product from
malfunctioning, becoming inoperable, or the performance and/or the
device from being adversely affected:
1. Cable
· Be sure to turn off the power before connecting or disconnecting the
cables.
2. Optical axis
· The center of the optical axis may disperse by camera. When
mounting a camera, always check the central position of video images
with a monitor.
· The center of CCD and the optical axis of the lens are aligned to the direction
of the camera at time of shipment. When the camera direction is changed,
the gap of center of optical axis may become large.
3. Cleaning
· Do not use thinners, benzene, acetone, kerosene to clean the Camera.
· Wipe off stubborn stains carefully with a piece of soft cloth that has
been wetted with a trace quantity of alcohol.
4. Static electricity
White LEDs are used for the illumination. White LEDs are easily
damaged by static electricity. A grounded wrist strap should thus
be used when installing or conducting maintenance on the Camera.
5. Magnification
· To avoid collisions of inside lens, maximum value for magnification
setting varies in relation to the focusing value. If magnification is not
sufficient, adjust the working distance.
6. Other Precautions
· When the extension connector on the back of the camera is not in use,
be sure to cover the connector with the attached cap.
Main unit, instruction sheet (this manual) and hexagonal wrench
＊
Applicable standard: IEC60825-1:1993 +A1:1997 +A2:2001
Make adjustment after disconnecting cable from the connector.
Loosen 3 screws located on the ring portion in the figure below using
the attached hexagonal wrench. Turn the ring to adjust the direction.
After adjustment, tighten the screws securely.
■
Connection
(1)Using the Camera cable FZ-VS,FZ-VSL,FZ-VSB
(sold separately),connect the connector on the back of the camera and
the camera connector on Controller FZ-3
□□
.
PRECAUTIONS FOR CORRECT USE
FZ-SLC100
To ensure safety, do not use this product for direct or indirect
detection of data from human body.
Do not use this product as a sensing device for the protection
of the human body.
Beware of danger of burns.
Do not touch the case while the LED is ON or immediately after
the power is turned OFF, since it is extremely hot.
Since this product emits a visible light, that may have an adverse
effect on the eyes. Do not stare directly into the light emitted from the
LED. If the subject has a specular reflective surface, take care not to
allow reflected light enter your eyes.
CAUTION
WARNING
659 (H) x 494 (V)
1/3-inch interline color CCD
(reading all pixels)
7.4 (µm) x 7.4 (µm)
Non-interlace mode
80.600Hz
39.336KHz
30.682MHz
12 lines to 480 lines
Internal synchronization
Digital, 10 bit
0dB to +13dB
1/120, 1/200, 1/500, 1/1000,
1/2000, 1/4000, 1/8000, 1/20000s
Electrically driven magnification, focusing and iris
Zoom
Vari-focal
Range of view
13 to 100 mm, with tol/- 5% maximum
Working distance
70 mm to 190 mm
Resolution
480 TV minimum
F value
Minimum: F2.8 (W-end) to F4.7 (T-end)
Range of W-end : 2.8 to 8.0
Motor durability
(One(1) time is equivalent
to one (1) reciprocating motion)
Magnification and focusing:
10,000 times minimum
Iris: 20,000 times minimum
Light source
White LED
(Wavelength: 400 nm to 700 nm)
Lighting system
8-block lighting with variable illumination intensity
Mean life
5,000 hours
(Time required for the illumination intensity to drop to 50%
of original level at shipment under constant lighting condition
at maximum intensity with the ambient temperature of 25°C)
LED class
＊
Class 2
FZ-SLC100
Item
Power consumption
Vibration
resistance
Shock resistance
Ambient
Temperature
Ambient
humidity
Ambient environment
IEC60529 IP20
Degree of protection
Material
Weight
Maximum 5 m (when using optionally available FZ-VS)
Cable length
(Unit: mm)
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury or in
property damage.
CAUTION
Indicates a potentially hazardous situation which, if not
avoided, will result in minor or moderate injury, or may
result in serious injury or death. Additionally there may
be significant property damage.
WARNING
Camera cable
connector
Extension
connector
Intelligent camera
FZ-SLC100
Nameplate
Camera cable
FZ-VS
□
100
100
28
2
68
101.5
40
28
73.2
87.4
(5.2)
20
±0.1
53
7.4
2-M4 8.0 deep
1/4-20UNC 8.0 deep
(47)
37.5
27.5
© OMRON Corporation 2006-2007 All Rights Reserved.
OMRON Corporation
Suitability for Use
EUROPE
OMRON EUROPE B.V. Sensor Business Unit
Carl-Benz Str.4, D-71154 Nufringen Germany
Phone:49-7032-811-0 Fax: 49-7032-811-199
NORTH AMERICA
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,IL 60173-5302 U.S.A
Phone:1-847-843-7900 Telephone Consultation
1-800-55-OMRON Fax : 1-847-843-7787
ASIA-PACIFIC
OMRON ASIA PACIFIC PTE LTD
83 Clemenceau Avenue,#11-01 UE Square,Singapore 239920
Phone : 65-6-835-3011 /Fax :65-6-835-2711
n
THE PRODUCTS CONTAINED IN THIS SHEET ARE NOT SAFETY RATED.
THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF
PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY
COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES.
Please refer to separate catalogs for OMRON's safety rated products.
OMRON shall not be responsible for conformity with any standards, codes, or
regulations that apply to the combination of the products in the customer's
application or use of the product.
Take all necessary steps to determine the suitability of the product for the
systems, machines, and equipment with which it will be used.
Know and observe all prohibitions of use applicable to this product.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
EN 60825-1:1994 +A1:2002 +A2:2001
Observe the following precautions to ensure safe use of the Camera.
1. Installation Conditions
· To ensure safety in operation and maintenance, do not install the
Camera close to high-voltage equipment or power equipment.
PRECAUTIONS FOR SAFE USE
*The camera cable (FZ-VS,FZ-VSL,FZ-VSB) is polarized, so, make sure that the
end bearing a name plate is connected to the controller.
Thank you for selecting OMRON product. This sheet pri-
marily describes precautions required in installing and
operating the product.
Before operating the product, read the sheet thoroughly to
acquire sufficient knowledge of the product. For your con-
venience, keep the sheet at your disposal.
NOTICE:
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to adequate measures.
TRACEABILITY INFORMATION:
Representative in EU
Omron Europe B.V.
Carl-Benz-Str.4
71154 Nufringen Germany
Manufacturer
Omron Corporation,
Sensing Devices & Components Div.H.Q.,
Application Sensors Division
Shiokoji Horikawa, Shimogyo-ku,
Kyoto, 600-8530 JAPAN
