Ratings and Specifications
LED Indicators
*1. The indicator of the emitter is illuminated only in the case the Wired Synchronization
is enabled and is off in the case the Optical Synchronization is enabled.
*2. DIP switches is on the Intelligent Tap.
*3. Refer to the F3SG-SR User's Manual for more information on blinking patterns.
Note: In the SETTING state to make settings with the SD Manager 3, the TEST,
LONG and CODE indicators on the emitter and the CFG, PNP and CODE indicators
on the receiver blink. (TEST: Yellow, LONG/CODE: Green, CFG/PNP/CODE: Green)
■
LED Indicators of the Receiver
CODE
or
C
ERR
or
E
OSSD
or
O
MAINT
or
M
PNP
or
P
CFG
or
F
SEQ
or
S
■
LED Indicators of the Emitter
1
2
3
4
6
7
Scan code
Lockout
Operating range
Test
Top-beam-state (*1)
Bottom-beam-state (*1)
Green
OFF
Red
Green
OFF
Yellow
Blue
Blue
Code A is selected
Automatic interference prevention by wired synchronization being performed
LOCKOUT state. The indicator is illuminated in the emitter of
another sensor segment than that having a lockout error
(between the emitter and receiver in the Wired Synchronization)
Long Mode is selected
Short Mode is selected
---
The top beam is unblocked
The bottom beam is unblocked
---
LOCKOUT state. The indicator is illuminated in the emitter of a sensor segment having a lockout error
LOCKOUT state due to Operating range selection setting error
---
External Test is being performed
MUTING/OVERRIDE state, or LOCKOUT state due to Other sensor error
MUTING/OVERRIDE state, or LOCKOUT state due to DIP Switch setting error (*2)
Location
Indicator
Name
Color
Illuminated
Blinking
Location
Indicator
Name
Color
Illuminated
Blinking
TOP
BTM
CODE
or
C
ERR
or
E
LONG
or
L
TEST
or
T
1
2
3
4
5
6
7
9
10
Scan code
Lockout
ON/OFF
Maintenance
PNP/NPN mode
Configuration
Sequence
Top-beam- state
Bottom- beam-state
Green
OFF
Red
Green
Red
Red
Orange
Green
OFF
Green
Yellow
Blue
Blue
Code A is selected
Automatic interference prevention by wired synchronization being performed
LOCKOUT state. The indicator is illuminated in the receiver of another sensor
segment than that having a lockout error (when in cascade connection or
between the emitter and receiver in the Wired Synchronization)
Safety outputs are in ON state
Safety outputs are in OFF state
LOCKOUT state due to a recoverable error
Safety outputs are instantaneously turned OFF due to ambient light,
vibration or noise. Or sequence error in Muting, Pre-Reset or PSDI
PNP is configured
NPN is configured
Fixed or Floating Blanking, Reduced Resolution, Warning Zone
or Slow mode of Response Time Adjustment is enabled or
after the Muting zone is determined by the Dynamic Muting function.
INTERLOCK state
The top beam is unblocked
The bottom beam is unblocked
---
LOCKOUT state. The indicator is illuminated in the receiver of a sensor segment having
a lockout error
---
LOCKOUT state due to Safety Output error, or error due to abnormal power supply or noise
LOCKOUT state due to a replacement- recommended error
Intelligent Tap is in the LOCKOUT state
Polarity of PNP is changed to NPN, or vice versa, during operation, and internal circuit is defective
---
TEACH-IN mode, zone measurement being performed by Dynamic Muting, or LOCKOUT
state due to Blanking monitoring error, Configuration error or Parameter error
Sequence or sequence error in Muting, Pre-Reset or PSDI (*3) or Teach-in error
MUTING/OVERRIDE state, or LOCKOUT state due to Other sensor error
MUTING/OVERRIDE state, or LOCKOUT state due to DIP Switch setting error (*2)
TOP
BTM
Type 4: ±2.5° max.*, Type 2: ±5.0° max.* (*Emitter and receiver at operating range of 3 m or greater)
Infrared LEDs, Wavelength: 870 nm
SELV/PELV 24 VDC±20% (ripple p-p 10% max.)
See F3SG-SR/PG User's Manual for more information.
Two PNP or NPN transistor outputs (PNP or NPN is selectable by wiring of power supply.), Load current: 300 mA max.,
Residual voltage: 2 V max. (except for voltage drop due to cable extension), Capacitive load: 1 µF max., Inductive load: 2.2 H max.(*1 *2),
Leakage current: 1 mA max.(PNP), 2 mA max.(NPN)(*3)
*1. The residual voltage is 3 V max. when the Intelligent Tap is connected to the sensor.
*2. The load inductance is the maximum value when the safety output frequently repeats ON and OFF. When you use the safety output
at 4 Hz or less, the usable load inductance becomes larger.
*3. These values must be taken into consideration when connecting elements including a capacitive load such as a capacitor.
One PNP or NPN transistor output (PNP or NPN is selectable by wiring of power supply.) Load current: 100 mA max.,
Residual voltage: 2 V max.(*) *The residual voltage is 3 V max. when the Intelligent Tap is connected to the sensor.
Light emission stops when connected to 24 V DC
ON voltage: Vs-3 V to Vs (short circuit current: approx. 5.0 mA) *, OFF voltage: 0 V to 1/2 Vs, or open (short circuit current: approx. 6.0 mA) *
Light emission stops when connected to 0 V DC
ON voltage: 0 to 3 V (short circuit current: approx. 6.0 mA), OFF voltage: 1/2 Vs to Vs, or open (short circuit current: approx. 5.0 mA) *
Long: 12 V to Vs (short circuit current: approx. 4.2 mA) * or open
Short: 0 to 3 V (short circuit current: approx. 4.2 mA)
PNP ON voltage: Vs-3 V to Vs (short circuit current: approx. 9.5 mA) *, OFF voltage: 0 V to 1/2 Vs, or open (short circuit current: approx. 13.0 mA) *
NPN ON voltage: 0 to 3 V (short circuit current: approx. 13.0 mA), OFF voltage: 1/2 Vs to Vs, or open (short circuit current: approx. 9.5 mA) *
PNP ON voltage: Vs-3 V to Vs (short circuit current: approx. 4.5 mA) *, OFF voltage: 0 V to 1/2 Vs, or open (short circuit current: approx. 7.0 mA) *
NPN ON voltage: 0 to 3 V (short circuit current: approx. 7.0 mA), OFF voltage: 1/2 Vs to Vs, or open (short circuit current: approx. 4.5 mA) *
Output short-circuit protection
Optical synchronization by Scan Code: fixed Wired synchronization: in up to 3 sets
(See F3SG-SR/PG User's Manual for more information.)
Interlock, External Device Monitoring (EDM) Pre-Reset, PSDI, Fixed blanking/Floating Blanking, Reduced Resolution, Muting/Override,
Mutual Interference Prevention, PNP/NPN Selection, Response Time Adjustment (See F3SG-SR/PG User's Manual for more information.)
Operating: -30 to 55 °C (non-icing), Storage: -30 to 70 °C
Operating: 35% to 85% (non-condensing), Storage: 35% to 95%
IEC 60529: IP65 and IP67, DIN40050-9: IP69K
In optical synchronization: 100 m max* between power supply and emitter and between power supply and receiver
In wired synchronization: 100 m max* between power supply and emitter, between power supply and receiver, and between emitter and receiver
* When the Intelligent Tap (F39-SGIT-IL3) is connected to the sensor, this applies in the case of the rated power supply of 24 VDC to 24 VDC +20%.
See F3SG-SR/PG User's Manual for more information.
Instruction Sheet, Quick Installation Manual, Troubleshooting Sticker
1.1×10
-8
max. (IEC 61508)
Opaque objects, 14-mm dia.
320 to 1,800 mm
0.3 to 8.0 m *
0.3 to 2.4 m *
Optical synch.: 8 to 18 ms, Wired synch.: 10 to 21 ms
Optical synch.: 40 to 90 ms, Wired synch.: 50 to 105 ms
Optical synch.: 16 to 36 ms, Wired synch.: 20 to 42 ms
Optical synch.: 80 to 180 ms, Wired synch.: 100 to 210 ms
Optical synch.: 32 to 72 ms, Wired synch.: 40 to 84 ms
Optical synch.: 160 to 360 ms, Wired synch.: 200 to 420 ms
Optical synch.: 64 to 144 ms, Wired synch.: 80 to 168 ms
Optical synch.: 320 to 720 ms, Wired synch.: 400 to 840 ms
Opaque objects, 25-mm dia.
320 to 1,840 mm
0.3 to 16.0 m
0.3 to 5.6 m
Optical synch.: 8 to 13 ms, Wired synch.: 10 to 17 ms
Optical synch.: 40 to 65 ms, Wired synch.: 50 to 85 ms
Optical synch.: 16 to 26 ms, Wired synch.: 20 to 34 ms
Optical synch.: 80 to 130 ms, Wired synch.: 100 to 170 ms
Optical synch.: 32 to 52 ms, Wired synch.: 40 to 68 ms
Optical synch.: 160 to 260 ms, Wired synch.: 200 to 340 ms
Optical synch.: 64 to 104 ms, Wired synch.: 80 to 136 ms
Optical synch.: 320 to 520 ms, Wired synch.: 400 to 680 ms
* When operating at an ambient temperature of -10 to -30°C, use the F3SG-SR with the operating range of 0.3 to 4.0 m in Long Mode and 0.3 to 1.2 m in Short Mode.
Model
F3SG-
□
SRB
□□□□
-14-K
F3SG-
□
SRB
□□□□
-25-K
Performance
Electrical
Functional
Environmental
Connections
Weight
Accessory
Conformity
*Selectable by SD Manager 3.
*The Vs indicates a supply voltage value in your environment.
Object resolution (Detection capability)
Protective height
Operating
range
Response
time
Effective aperture angle (EAA) (IEC 61496-2)
Light source
Power supply voltage (Vs)
Current consumption
Safety outputs (OSSD)
Auxiliary output
Input
voltage
Protective circuit
Mutual interference prevention
Safety-related functions
Ambient temperature
Ambient humidity
Degree of protection (IEC 60529)
Cable
extension
PFH
D
See F3SG-SR/PG User's Manual for more information on cable extension.
Long
Short
Normal mode
×2 Slow
mode *
×4 Slow
mode *
×8 Slow
mode *
ON to OFF
OFF to ON
ON to OFF
OFF to ON
ON to OFF
OFF to ON
ON to OFF
OFF to ON
TEST
OPERATING RANGE
SELECT Input
RESET/EDM
MUTE A/B,
PRE-RESET
Root cable
