background image

4

Modular Temperature Controller for Gradient Temperature Control

 

EJ1G

Communications Specifications

Note: 1.

Connection from the EJ1C-EDU

2.

A special cable (EJ1C-CBLA050) must be purchased separately for the G3ZA connection.

3.

For the number of Units that can be connected, refer to 

“Connection Precautions”

 on page 9.

4.

When performing gradient temperature control, the number of control channels is limited by the group setting. For details, refer to 

“Gradient Group Settings”

 on page 11.

Current Transformer (CT) 
Rating

Characteristics of the Heater 
Burnout Alarm and Heater Short 
Alarm 

(TC2 Models Only)

Note: 1.

When the control output ON time is 100 ms or less, heater 
burnout detection and heater current measurement are not 
performed.

2.

When the control output OFF time is 100 ms or less, heater 
short alarm and leakage current measurement are not 
performed.

Item

Port A Terminal/ Port A Connector  

(See note 1.)

G3ZA Connection Port 

(See note 2.)

Transmission path connection

RS-485 (multipoint)

Communications method

RS-485 (two-wire, half duplex)

Synchronization method

Start-stop synchronization

Baud rate

38.4 kbps fixed

57.6 kbps fixed

Transmission code

ASCII

Data bit length

7 bits

Stop bit length

2 bits

Error detection

Vertical parity (even)

Block check character (BCC): with CompoWay/F

Flow control

None

Interface

RS-485

Retry function

None

Communications response wait time

1 to 99 ms (default: 1 ms)

---

Number of Units that can be connected in 
parallel (See notes 3 and 4.)

16 Units (model numbers with TC4: 64 channels, 
model numbers with TC2: 32 channels)
Communications connection via port A on the 
End Unit

8 Units (Communications connection via G3ZA 
port on the Basic Unit)

Dielectric 
strength

1,000 VAC for 1 min

Vibration 
resistance

50 Hz, 98 m/s

2

Weight

E54-CT1: Approx. 11.5 g, E54-CT3: Approx. 50 g

Accessories 
(E54-CT3 only)

Armatures (2), plugs (2)

Maximum 
heater current

100 A AC

Input current 
indication 
accuracy

±

5%FS 

±

1 digit max.

Heater 
burnout alarm 
setting range

0.1 to 99.9 A (in units of 0.1 A)
0.0 A: Heater burnout alarm output turns OFF.

100.0 A: Heater burnout alarm output turns ON.

Min. detection ON time: 100 ms (See note 1.)

Heater short 
alarm setting 
range

0.1 to 99.9 A (in units of 0.1 A)
0.0 A: Heater short alarm output turns ON.

100.0 A: Heater short alarm output turns OFF.

Min. detection OFF time: 100 ms (See note 2.)

Summary of Contents for EJ1C-EDUA-NFLK

























Reviews: