background image

16

2-1-2.  Stationary installation

 

Perform installation only as shown in the diagrams below.

● 

Horizontal installation

  Attach the included rubber feet for horizontal installation (14.5 mm depth) to the round stickers on the 

unit (4 locations) and position the unit horizontally.

  For stationary horizontal installation, make sure that this product does not slide or fall.
  Install the UPS (BU100RW/BU200RW/BU300RW) so that it sits on top of the additional battery unit 

(BUM100R/BUM300R).

BUM300R

● 

Upright installation

 

Use the stand that was included with the UPS (BU100RW/BU200RW/BU300RW). 

  Attach the 4 rubber feet for vertical placement (height: 1.7mm) to the 4 points on the bottom surface 

(see diagram below). 

  (Attach the rubber feet included with the UPS to the 4 points on the bottom surface of the unit. 
  Attach one rubber foot included with the UPS to the bottom surface of each piece of the vertical 

stand.) 

BU300RW

Do not slide the unit when the rubber feet are touching the 

fl

 oor. 

BU200RW/

BU300RW

  Caution

Free-standing installation 
When positioning the unit vertically, use the 

fi

 xing brackets for the vertical stand included with the unit. 

When positioning the unit horizontally, attach the rubber feet to the bottom surface of the unit to pre-
vent it from sliding or falling. 

BUM300R

BATTERY UNIT

BUM100R

BU100RW

Summary of Contents for BUM100R































Reviews: