background image

13 

 

LIMITED WARRANTY 

Omegasonics warrants the OMG-3600PW prewash cleaner for a period of two (2) years 
from the date of delivery, when used in accordance with the manufacturer

’s instructions.  

During the warranty period, Omegasonics will repair or replace free of charge at an 
authorized repair service center all parts that are defective because of material or 
workmanship.  Freight charges to an authorized service centers are the responsibility of 
the user.  

 

This warranty does not include damage or product failure, which results from cavitation 
erosion, misuse, abuse or transportation damage.  This warranty is limited to the 
original purchaser and is not transferable.  Total liability for any reason whatsoever, 
shall not in any case exceed the cost of repair or replacement of the defective part.  In 
no case shall Omegasonics be responsible for any incidental or consequential 
damages.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Omegasonics 
330 East Easy Street, Suite A  
Simi Valley, CA  93065 
(805) 583-0875 
(805) 583-0561 fax 
Email:  [email protected] 

 

www.omegasonics.com

  

 

 

 

 

M-OMG3600PW-0517 

Summary of Contents for RESTORATION PRO 3600PW





















Reviews: