background image

 

 

INSTALLATION 

 

UNPACKING THE APPLIANCE 

 

Remove the external & internal packaging. 
When unpacking the appliance please check for any damage. If damage is found, do not connect to the power 
source and contact the Authorised Service Provider. Check that the following items are contained within the 
packaging: 

 

1 Storage Basket    

 

 

1 Instruction Manual 

Before connecting the freezer to the power source, let it stand upright for approximately 4 hours. This will reduce the 
possibility of a malfunction in the cooling system from handling during transportation. Remove any protective film 
from the outer surface. 
Clean the interior surface with lukewarm water using a soft cloth. 

 

INSTALLING THE FREEZER 

 

This appliance is designed to be free standing only, and should not be recessed or built-in. 
Place your freezer on a level floor that is strong enough to support the freezer when it is fully loaded.  

Allow at least 10 cm of space between the back and sides of the freezer, which allows the proper air circulation, 
and at least 70cm above the unit.  
Locate the freezer away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may 
affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient 

temperatures may also cause the freezer not to perform properly. Avoid locating the freezer in moist areas.  
Plug the freezer into an exclusive, properly installed-grounded wall outlet. Do not under any circumstances cut or 
remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should 
be directed toward a certified electrician or an Authorised Service Centre. 
After plugging the appliance into a wall outlet, allow the unit to cool down for 2~3 hours before placing food in 

the freezer compartment. 

 
APPLIANCE DETAILS

 

 

ELECTRICAL DETAILS: 

 

Rated Voltage:                220-240 Vac 50 Hz. 
Supply Connection:         10 A domestic socket. 
Max Rated Inputs:           See data label on unit. 

 
This information can be found on the rating plate 
(data label) affixed to the rear of the appliance 
 
OCF380:  

Dimensions (WxDxH): 1300x700x845mm 
Weight: 50kg 
 
OCF316: 
Dimensions (WxDxH): 1120x700x845mm 
Weight: 44kg 

 
1. Internal handle. 
2. Drainage hole. 
3. Storage basket. 
4. Power cord (not shown). 

5. Control panel. 
6. Castors (2 fixed, 2 uni-directional). 

Summary of Contents for OCF316













Reviews: