background image

20

20

EN

Support Menu

Oil hours:

 

Indicates the hours remaining before the oil needs to be changed. 

Oil filter hours:

 

 Indicates the hours remaining before the oil filter needs to be changed.

Air filter hours: 

 

Indicates the hours remaining before the air filter needs to be changed.

Oil separator hours:

 Indicates the hours remaining before the oil separator filter needs to be changed.

Bearings lubric. hours

: Indicates the hours remaining before the main electric motor bearing needs to be lubricated.

Fan temperature:

   Defines the working temperature of the cooling fan. The threshold set has a hysteresis that can be 

changed by 10°C. e.g. if the operating temperature is set at 80°C, the fan will activate at 80°C and stop 

at 70°C (screw unit supply temperature).

No load time: 

 

Defines the motor stoppage time from the moment the load solenoid valve was deactivated because 

the desired pressure was reached.

Stoppage time:

  

Defines the stoppage time of the compressor from the moment in which stoppage is requested using 

the STOP(O) key. The solenoid valve is immediately deactivated.

Automatic start: 

  If the compressor is on, it starts automatically after an electricity cut. The first start should be activated 

by pressing the START (I) key on the panel.

Max start-up hours: 

Defines the maximum number of start-ups of the main electric motor within the arc of one hour. If 

surpassed, the compressor will stay on (loaded or with no load depending on the pressure) until the 

hour is up as calculated from first start-up and then returning to normal functioning.

Remote enabling:

   Remote command enabling.

Fan extra time:

  

Defines the time in which the cooling fan stays on after the working  temperature of the compressor has 

returned within the safety limits.

Inverter: 

 

Sub-menu for inverter configuration (see INVERTER MENU paragraph).

Fan temperature hysteresis:

 Defines the delta temperature in which the main cooling fan must work.

Diagnostic:

  

Using the diagnostic menu, you can control the various inputs and outputs of the control unit:

Input:

 

the status of 9 digital inputs can be controlled

Output:

 

using the right and left keys, you can move on the relay output you want to command, while using the 

up and down buttons to activate the output

AN1:

  

Indicates pressure in bar with centesimal precision

AN2:

 

Indicates the temperature in °C Screw probe

AN3: 

 

Indicates the temperature in °C Dryer probe

INV:

  

Indicates the inverter output automatically switches 4-20mA

Keeping the I key pressed, you can execute a motor start-up test. Pressing the 0 key, you can upload the default parameters 

(there are 32 sets of parameters present). The Factory password is required. Press the 

RESET

 key to execute calibration of the 

pressure transducer (the Factory password is required).

START-UP AND OPERATION

01

Start-up setting:

Programma 00 

Program

 01 

Program

 02 

Program

 03 

Program

 04 

Program

 05 

Start-up on

  Program0 

00:00 ...

Start time

....

00:00 ...

Stop time

 

00.0BAR.

No load pressure

 

00.0BAR.

Loaded pressure

 

Lun   Mar   Mer   Gio   Ven   Sab   Dom 

Back to previous menu not

saved

 

Saves the program and

goes back to previous menu

 

Changes the parameter

 

Selects the parameter

to change

 

Back to previous men

u

Enters the program

selected

Selects the desired

program

 

Program 00

Mon      Tues        Wed      Thurs       Fri          Sat          Sun

STORM 38 VS - Cod.197DD9910 - Rev.2 01/2016

NOBEL DV 22 CSA - Cod.197EE0622ML - Rev.1 03/2019

Summary of Contents for NOBEL 22 DV CSA




























Reviews: