INTRODUCTION
The pocket size meter is used to measurement of
light intensity with user selectable units of lux and
fc.
SAFETY INFORMATION
It is recommended that you read the safety and
operation instructions before using the absolute
pressure meter.
1. Only operate the measuring instrument properly,
for its intended purpose and within the parame-
ters specified. Do not use force.
2. Never store the product together with solvents,
acids or other aggressive substances.
3. Don’t keep in place with high Temp, or high
humidity.
4. When not use for long time remove battery.
SPECIFICATIONS
Range:
0 to 200000 lux, 0 to 18580 fc
Units:
lux, fc
Resolution:
1 lux (0 to 19999), 10 lux (20000 to 200000)
1 fc (0 to 18580)
Spectral response:
CIE photopic.
The CIE photopic curve is an international
standard for the color response of the average
human eye.
Spectral angle:
ƒ′
1 < 8%
Acceptance angle:
ƒ′
2 <2% cosine corrected (150°)
Total accuracy for CIE standard illuminant A
(2856K):
±(3%rdg + 10dgts)
CIE standard illuminant A can be realized by
means of CIE standard source A, which is de-
fined as:
A gas-filled tungsten-filament lamp
operating at a correlated color temperature of
2856K.
Accuracy:
Stated accuracy at 23°C±5°C, <70% R.H.
Temperature Coefficient:
0.1 times the applicable
accuracy specification per °C out of 23°C±5°C.
Measurement rate:
1 times/second.
Operating environment:
0°C to 50°C at <70%
R.H.
Storage temperature:
-20°C to 50°C, 0 to 80%
R.H. with battery removed from meter.
Battery:
1.5V (AAA size) x 2pcs.
Battery Life:
180 hours typical.
Low battery indication:
The “
” is displayed
when the battery voltage drops below the oper-
ating level.
Dimensions:
24.7mm (T) x 50.9mm (W) x 132.9 mm (H).
Weight:
Approx. 116g including batteries.
OPERATIONS
There are 3 operation modes, namely Measure-
ment Mode, Set Mode and Hold Mode.
1. Turning on and off the meter:
When
power
is off, a short push on “ ” key turns
on the meter and enter Measurement Mode.
When power is
on
, press and hold “ ” key for 2
seconds turns the power off.
Right
after
power on, all the indicators on the
LCD display lights up for one second.
2. Measurement Mode:
When power is on, the meter starts measuring
and refresh every second.
Changing unit:
In measurement mode, press “ ” key to switch
between lux and fc.
Backlight:
In measurement mode, a short push on “ ” key
turns on the backlight for dark environment, it
goes off automatically after 15 seconds if without
further operation.
3. Set Mode:
In set mode, user can turn on/off APO function.
(APO = Auto Power Off, when APO is ON, the
meter power off automatically if no operation in
10 minutes)
When power is off, press and hold “ ” key for 2
seconds to enter Set Mode.
Short push on “ ” key switches between ON
and OFF.
Push “MODE” key to save the setting, exit APO
setting mode and enter measuring mode.
Note:
※
To turn off power in Set Mode abandon
the current setting and previous settings
remain unchanged. If “
” indicator
appeared, the setting value can works till
power off but did not save to meter.
4. Hold Mode:
In Measurement Mode, short push “Mode” key
to enter Hold Mode with indicator “
HOLD
”
shows at upper left corner of LCD.
Right after entering this mode, shown in the LCD
is the last measurement and the reading will not
be updated with new measurement.
Push “Mode” key each time the display changes
in following sequence:
(1) Last Measurement: with indicator “HOLD”.
(2) Maximum value recorded: with indicator
“HOLD” + “MAX”.
(3) Minimum value recorded: with indicator
“HOLD” + “MIN”.
(4) Maximum-Minimum value recorded: with
indicator “HOLD” + “MAX-MIN”.
(5) Average of values recorded: with indicator
“HOLD” + “AVG”.
(6) Exit the Hold Mode and return to Measure-
ment Mode.
To clear the recorded values:
In Hold Mode and during viewing MAX, MIN,
MAX-MIN or AVG, press and hold “Mode” key
for 2 seconds, to clear the recorded data and re-
turn to measurement mode.
MAINTENANCE
Installing and Replacing Battery
A. Battery Cover
B. Battery
1. Power is supplied by 2pcs 1.5V (AAA SIZE).
2. The “
” appears in the display when battery
replacement is needed.
3. Push the Battery Cover and lift it in the direction
as shown in the figure.
4. Remove the batteries from battery compartment.
5. Replace with 2 new AAA batteries with polarity
as indicated on the bottom of Battery Compart-
ment.
6. Replace the Battery Cover.
Cleaning
Periodically wipe the case with a damp cloth and
detergent, do not use abrasives or solvents.
HHC230
Light Meter
INSTRUCTION
SHEET
M5512/
04
1
8
Shop online at omega.com e-mail: [email protected]
For latest product manuals: omegamanual.info
LIGHT METER
HHC230
