Page - 5
Excalibur Gold Advanced System Features
Automatic Transmitter Verification
TM
: Your Excalibur Gold vehicle security system is
protected against a weakness which is shared by all other remote security systems, even
factory-equipped Remote Keyless Entry systems: a thief's ability to code his own, unauthorized
transmitter to operate your system for the purpose of stealing your vehicle or it's contents.
Also, in normal operation, every time the ignition switch is turned "on", the LED Status
Indicator will flash and pause for ten seconds, the number of flashes between each pause being
equal to, and confirming, the number of transmitters encoded to operate your system. For
example: two flashes and a pause indicate that only two transmitters are coded to operate your
system. In the event the system alerts you to a recent transmitter addition, or if the LED Status
Indicator flashes a total different from the number of transmitters you have programmed to
operate your system, you can now immediately reprogram your transmitters, effectively
erasing any unauthorized transmitters.
IMPORTANT NOTE: For the first 48 hours after your new system
is installed, every time the ignition switch is turned "on", the siren
will chirp rapidly (or the horn will honk rapidly) for two seconds, and
the LED Status Light will flash for 90 seconds. This will also occur
in
the event of a new transmitter code being entered into the system.
Page - 6
The Patented Automatic Transmitter Verification
TM
feature is the industry's first response
addressing the growing problem of a professional thief defeating a vehicle security system
by coding his own transmitter to operate the system. Previously, garage door openers were
commonly duplicated by burglars to gain home entry. Now when you leave your vehicle and
keys with any individual for any reason, you will have the peace of mind of knowing that only
your transmitters will operate the security system and that no other person has coded extra
transmitters to steal your vehicle.
Transmitter Code Jumping
TM
: When the remote control transmitter is operated, a switch
upon it is pressed so that it may transmit an encoded Radio Frequency (RF) signal. The word
"frequency" denotes the wavelength of the signal, and the encoding is a digital message within
the signal which ensures the correct command is followed by the proper receiving system. A
common analogy used to illustrate this is a common pocket radio - the frequency denotes where
to turn the radio's dial to hear a particular program, and the encoding is the language and words
which, if correct, are understood by the listener.
Each time you transmit a code to the security system, the transmitter and security system
will advance to another code to use for the transmission. The Code Jumping
TM
Transmitter
prevents a thief from using a "code grabber" device to record and play back a transmission
for the purpose of disarming your vehicle security system. Please note that pressing the
transmitter's arm / disarm button many times while it is out of range of the security system can
advance its codes beyond the range of recognition. If this occurs, simply press the arm / disarm
button a few times within range of the system to re-synchronize the Code Jumping
TM
sequence
between the transmitter and the security system control module.
Transmitter Operations
Page - 7
Small Center Button-
If this button is held for 3
seconds, the security system
will activate the trunk release
function.
If this button is pressed and
then the large button is
pressed within 3 seconds, the
security system will arm or
disarm without audible con-
firmation.
If this button is pressed within
3 seconds after arming the
system, the Auxiliary sensor
will be deactivated.
If this button is pressed within
3 seconds after disarming, the
system will enter Remote Va-
let.
Large Upper Button- Press-
ing and releasing this but-
ton will arm and disarm the
security system. If the op-
tional doorlock interface is
installed, the doors will lock
upon arming, and unlock
upon disarming.
Pressing and holding this
button for 3 seconds will
"Panic" the system- which
will sound the siren (or horn),
flash the exterior lights, and
also lock the doors.
Red LED Light- Illumi-
nates and confirms
transmission when a
button is pressed.
Small Lower Button-
Pressing this button for 3 seconds may be used to activate
other optional equipment, such remote car starting units; or
the programmable Anti-Carjacking feature (Page 26).
Page - 8
The Remote Transmitter
Transmitter Button Operation: The transmitter's three buttons individually control the
system's functions; and certain other operations may be performed by first pressing and
releasing one, then another button in sequence. Complete transmitter button operations are:
1)
Arm / Lock: (System Disarmed) Press and release the Large Upper Button.
2)
Disarm / Unlock #1: (System Armed) Press and release the Large Upper Button.
3)
Remote Panic Feature: (At any time) Press and hold the Large Upper Button 3
seconds.
4)
Trunk Release Output: (At any time) Press and hold the Small Center Button 3
seconds. This operation also disarms the system (if armed).
5)
3rd Channel Output: (At any time) Press and hold the Small Lower Button for 3
seconds. If the Anti-Carjacking Feature is programmed to operate, it will be activated
if the ignition switch is on and 3rd Channel Output is operated.
6)
Silent Arm / Lock: (System Disarmed) Press and release the Small Center Button,
then press and release the Large Upper Button.
7)
Silent Disarm / Unlock: (System Armed) Press and release the Small Center
Button, then press and release
the Large Upper Button.
8)
Arm and bypass the Auxiliary Sensor: (System Disarmed) Press and release the
Large Upper Button, then press and release the Small Center Button.
9)
Disarm, then Remote Valet: (System Armed) Press and release the Large Upper
Button, then press and release the Small Center Button.
