ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
START HERE
ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
2
ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
3
ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
4
The instrument is a panel mount device protected in accordance
with EN61010-1 (Safety requirements for electrical equipment
for measurement, control, and laboratory standard). Remember
that the unit has no power-on switch. Building installation should
include a switch or circuit-breaker that must be compliant to IEC
947-1 and 947-3.
SAFETY:
• Do not exceed voltage rating on the label located on the top
of the instrument housing.
• Always disconnect power before changing signal and power
connections.
• Do not use this instrument on a work bench without its case
for safety reasons.
• Do not operate this instrument in flammable or explosive
atmospheres.
• Do not expose this instrument to rain or moisture.
EMC:
• Whenever EMC is an issue, always use shielded cables.
• Never run signal and power wires in the same conduit.
• Use signal wire connections with twisted-pair cables.
• Install Ferrite Bead(s) on signal wire close to the instrument if
EMC problems persist.
To Select Operating Mode
(Rate or Total):
1.
Press MENU until the
display shows
Func
.
2.
Press SET to show
the current mode.
3.
Press SET to
select between
rAtE
and
totAL
.
4.
Press MENU to store
the mode into volatile
memory.
To store the operating mode (or any value)
into non-volatile memory:
•
Press MENU until the meter displays
noStor
.
•
Press /SET once to display
StorE
.
•
Press MENU again.
The value is stored in non-volatile memory.
3-Wire Sensor
Open Collector
(PNP)
2-Wire Contact
Closure
2-Wire
Magnetic
Pickup
Using the Menus
Menu
Menu
Prompt is starting
Prompt
Item
point:
Func
Function
to select rate or totalize
mode.
SCALE
Scale Factor
to select scale factor
as a divider or multiplier
C
S
.
A
and to enter scale
A/SC
factor value.
OFFSEt
Offset Value
to select offset value.
Reading on meter =
input x scale + offset
dEC Pt
Decimal Point to select position of
decimal point in the
digital display.
SP LO
Setpoints
to enter setpoints.
Low and
Shows only if
SP HI
High
the relay option
board is installed.
COnFIG
Configuration to program internal
software switches to
specify analog,
output, RS-232 input
or alarm conditions
An LO
Analog Low
to obtain reading for
low analog output.
An HI
Analog High
to obtain reading for
high analog output.
NoStor
No Store
to save to the volatile
(active) memory
StorE
Store
to save to the non-
volatile (permanent)
memory.
RECALL
/ADV
MENU
RESET
/SET
Func
RECALL
/ADV
MENU RESET
/SET
rate
totAL
RECALL
/ADV
MENU RESET
/SET
RECALL
/ADV
MENU RESET
/SET
store
Wiring Examples
EXC
RTN
1
2
3
4
5
6
OPEN
OPEN
OPEN
CLOSED
OPEN
CLOSED
OPEN
OPE
N
CLOSED
OPEN
OPEN
OPEN
POSITIVE THRESHOLD
1K PULL DOWN RESISTOR TO RTN
243K PULL UP RESISTOR TO +EXC
S1
1
2
3
4
5
6
7
8
9
10
TB2
12.4 V
OUTPUT
EXC OUT
SIG IN
SIG RTN
RST IN
EXT GATE
BATTERY
EXCITATION = 12.4V
1
2
3
4
5
6
12.4V EXC
OPEN
OPEN
OPEN
CLOSED
OPEN
CLOSE
D
CLOSED
OPE
N
CLOSED
OPEN
OPEN
OPEN
HIGH LEVEL SIGNAL
POSITIVE THRESHOLD
LOW PASS FILTER
1K PULL DOWN RESISTOR
S1
1
2
3
4
5
6
7
8
9
10
TB2
EXC OUT
SIG IN
SIG RTN
RST IN
EXT GATE
BATTERY
243K PULL UP RESISTOR TO +EXC
1
2
3
4
5
6
EXCITATION= 5.0V
CLOSED
OPEN
CLOSED
OPEN
OPEN
CLOSE
D
OPEN
OPE
N
OPEN
OPEN
OPEN
OPEN
LOW LEVEL SIGNAL
ZERO THRESHOLD
NO FILTER
243K PULL-UP RESISTOR TO +EXC
S1
1
2
3
4
5
6
7
8
9
10
TB2
EXC OUT
SIG IN
SIG RTN
RST IN
EXT GATE
BATTERY
AC Powered Unit Connections
CAUTION: Do not connect AC power to your device until
you have completed all input and output connections. This
device must only be installed by a specially trained
electrician with corresponding qualifications. Failure to
follow all instructions and warnings may result in injury!
This device is marked with the international “Caution, risk of
danger” symbol.
External Fuse Required:
Time-delay, UL 248-14 listed
125 mA (115 Vac line)
63 mA (230 Vac line)
Time-lag, IEC 127-2 recognized
100 mA (115 Vac line)
50 mA (230 Vac line)
For complete wiring information on all setup
options, please refer to the Operator’s Manual.
Using this Quick Reference
Use this Quick Reference with your controller for information
on wiring and to make changes to the operating mode, scale
factor, and decimal point position. For detailed instructions,
refer to the appropriate section in the Reference Manual.
Safety Consideration
Mount the Unit
1. Cut a panel opening using the dimensions shown to the right.
2. Position the unit in the opening, making sure the front bezel is
flush with the panel.
3. Install retaining clips on both sides of the meter and tighten
against the panel.
Wiring
1. Remove the panel at the back
of the unit.
2. Locate the TB1 connector.
3. Insert the correct wire in each
terminal as shown in the
following figure and tighten the lockdown screws.
4. Tug gently on the wires to verify the connections.
