Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsin g them thorough ly.
When following this procedure from step1 to step 3, the filter system will be removed;
when following it from Step 3 to Step 1, the filter system will be installed.
It is dangerous to open the door when was hing, because the hot water may scald you.
When the wo rking cycle has fi nished, the buzzer of the dishwasher will soun d for 8 seconds, then stop. Turn off
t he appliance using the P owe r switch button, shut off the water supply and open the doo r of the dishwasher.
Wait for a few minutes bef ore unlo ading th e dishwasher to avoid ha ndlin g the dishes and utensils while th ey
are still hot and more susceptible to break age. The y will also dry better.
Switch Off the Dishwasher
The program light is on but is not blinking, only in this case the programme has ended.
Power
1.Switch off the dishwasher by pressing the
button.
2.Turn off the water tap.
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
If you ope n the door
, the machine will pause. The program light will
stop blinking and the buzzer will be
every minu te un less you close th e d oor . After
you close the door, the ma chin e will keep o n workin g after 1 0 se cond s.
during a w ash cycle
beeping
Premise:
A cycle that is underway can on ly be modified if it has only been running for a short time. Otherwise, the
detergent may have already be en released, a nd the appliance may have already drained the wash water.
If this is the case , the detergent dispenser mu st be refilled (see the section entitled " Loading the Detergent " ).
Press the Start/Pause button, the machine will pause, press the program button for more tha n 3
then
yo u can change the program to the desired cycle setting (see the section entitled " Starting a wash cycle. . ." ).
1
2
seconds,
A forgotten dish can be added any time before the detergent cup opens.
Add forgotten dishes.
Close the door
After the spray arms stop working,you can open the door
completely.
2
3
Open the door a little to stop the washing.
1
4
5
6
Press the Start/Pause button
Press the
button, the dishwasher will run
after 10 seconds.
Start/Pause
When you press th e Start/Pause button to pause during washing, the running indicato r will stop blinking and
the dishwashe r will
every minute unless you press the
button to start.
Start/Pause
be beeping
Starting a cycle wash
1
Draw out the lower and upper basket, load the dishes and push them back.
It is
to load the lower basket first, then the upper one (see the section entitl ed
Loading the Dishwasher
).
2
Pour in the detergent (see the section entitled
Detergent and Rinse Aid
).
3
Insert the plug into the socket. The power su pply is 220-240 VAC /50 HZ, the specification
of the socket is 10A 25 0VAC. Make sure that the water supply is turned on to full pressure.
4
Close the door, press the ON/OFF Button, and the display wi ll turn on.
5
Press the program Button to select your desired program.
“
”
“
”
If a program is selected, the response light will light. Then press the Start/Pause button, th e
dishwasher begins to start.
recommended
