manualshive.com logo in svg

Omega BB-4A, User Manual, Page: 7 / 24

Share
Download
Omega BB-4A User Manual Download Page 7

Section 2 - Installation

2.1 Unpacking

Remove the packing list and verify that you have received all your equipment. 

If you have any questions about the shipment, please call our Customer Service 

Department. 
We can also be reached on the Internet.
When you receive the shipment, inspect the container and equipment for any 

signs of damage. Note any evidence of rough handling in transit. Immediately 

report any damage to the shipping agent.

The carrier will not honor any damage claims unless all shipping material is saved for 

inspection. After examining and removing contents, save packing material and carton in 

the event reshipment is necessary.

The following items are supplied in the box:
• BB-4A Blackbody Calibration Source 

• Users Manual 

• Calibration Certificate 

• Power Cord 

• Reference Port Cord Plug Connector 

• Cavity Wood Shipping Plug (remove before use)

2.2 Mounting

Mount the unit on a bench, table top or shelf in a horizontal position and operate 

at least ten inches from any air obstructions to the fan, front panel, rear panel, 

bottom and top of the unit, in an ambient environment between the specified 0 

to 50°C (32 to 122°F). 

 

Your unit was shipped to you with a wood plug installed in the heater cavity to prevent 

damage during shipping. This plug must be removed before using your calibrator.

2.3 

Ambient Temperature

The target plate of the BB-4A can achieve any temperature within the specified 

temperature range when being operated in normal ambient temperature 

environments. The maximum specified heater cavity temperature of 982°C 

(1800°F) can be achieved over the entire specified ambient temperature range.

BB-4A Blackbody Calibrator

2

2-1

NOTE:

NOTE:

Summary of Contents for BB-4A

























Reviews:

No comments