background image

15

MENU  ITEMS

DISC LVL: Discrimination Level

Discrimination  allows  you  to  eliminate  metal  objects  from  detection.    It  is

adjustable from 0 to 80.  A discrimination setting of zero is not the same as All

Metal.  Discrimination incurs some loss of sensitivity to small and deep objects.

As you adjust the discrimination level, a number will appear in the center of the

LCD.  All targets that report a number LOWER than the set discrimination level

will  not  report  a  sound  or  display  activity.   They  have  been  eliminated  from

detection.  Note also that target category identifiers will start disappearing from

the top of the LCD screen as you increase the discrimination level. When a

target icon disappears, it means the whole category has been eliminated from

detection.      Lowering  the  DISC  LVL  setting  will  make  the  target  category

identifiers  return  to  the  screen,  even  if  they  are  partially  eliminated  by  the

numerical setting.

Access

: Press and release the MENU/Quick-Switch button until DISC LVL menu

item becomes active. Then use  and

to adjust the discrimination level. 

NOTCH: Selective Target Inclusion or Exclusion

a. The purpose of the NOTCH function is to change the detection status of

a target category and it functions only in DISCRIMINATION Mode.

• If a category was not eliminated from detection, then notching that category

will eliminate it from detection and the category icon will disappear.

•  If  a  category  was  eliminated  from  detection  (category’s  icon  not

illuminated), then notching the category will return the category to an

active state and the icon will reappear.

b. The following target categories can be notched in or out:

Foil,  Nickel,  P-Tab,  S-Cap,  Zinc,  Dime,  Qtr.  After  the  Qtr  category,

pressing NOTCH will exit the NOTCH function.

c. To select a category for notching, press NOTCH until the desired category

identifier flashes.  After a few seconds, the flashing will time out and the

current target category will be notched.

d. Practice pressing NOTCH a few times and its function will become obvious.

The NOTCH feature is not available in ALL METAL Mode.

Access:

Press and release 

until NOTCH menu item becomes active.

Then use  and

to select desired target category. Repeat the operation to

notch additional categories.

VOLUME

The audio response is limited by the volume setting and it applies to all of the

detector settings in all modes including user interface sounds and alarms.  In

addition to target volume it affects PINPOINT, Overload alarm, Ground Grab

over  metal  alarm  and  all  keypad  button  “beeps”.    It  does  NOT  affect  the

sensitivity of the detector.  The adjustable range is from 0 to 10.

Access

: Press and release 

until VOLUME menu item is activated. Use 

and

to modify the audio volume.

Volume continued on next pag

Summary of Contents for 8500





























Reviews: