3
PREPARATION
Assembly
(refer Fig. 1 & 2)
1. Make sure all parts are present. If any part is missing
or damaged, do not attempt to assemble, install or
operate the product. Contact Customer service.
2. Install ratchet bar into base frame with ratchet portion
of bar aligned with locking pawl.
3. Move the ratchet bar to its lowest position by raising
the locking handle, thereby releasing the stopper
and guiding the bar downward.
4. To help prevent inadvertent loss of the ratchet bar:
a) For 32035 & 32065:
(Tools required: Hammer and Punch)
Press the press tab inward using a suitable
hammer and punch.
b) For 32125:
(Tools required: 12mm Wrench)
Tighten the M7.5x20 hex bolt found on the collar.
Before Use
1. Verify that the product and the application are
compatible, if in doubt call Omega Tech. Service
(888) 332-6419.
2. Inspect stands before each use. Do not use if there are
bent, broken or cracked components noted (including
labels). Ensure that all parts move freely.
3. Read the operator's manual completely and
familiarize yourself thoroughly with the product and
the hazards associated with its improper use
before
using this product.
4. Always refer to the vehicle owners or service manual
for location of proper lift and support points.
OPERATION
Use only
on areas of the vehicle as specified
by the vehicle manufacturer.
Use ONLY
on
vehicles whose support points are
compatible
with
the saddle of the jack stand. Incompatibility may result
in structural damage to the vehicle and/or jack stand.
Structural damage to either may result in sudden and
unexpected loss of load height!
Only attachments and/or adapters supplied
by the manufacturer shall be used.
1. Adjust height by pulling up on ratchet bar.
2. The weight of locking handle should secure the
ratchet bar in desired position. To confirm this,
simply push down on the locking handle. Ensure
ratchet is secure before loading.
3.
Carefully
position jack stands so that load is centered
on stand’s saddle.
4.
Slowly
lower the vehicle onto the stands.
5. Check to ensure vehicle is secure before working on,
around or under. Use wheel chocks on all unlifted
wheels in both directions to prevent inadvertent
movement.
To lower load
Be sure that all tools and personnel are clear
before lowering load.
1. With suitable jack, raise vehicle clear of stands.
2. Carefully release stopper and allow ratchet to glide
down to lowest position.
3. Carefully remove stands, then carefully lower
vehicle with lift device.
MAINTENANCE
Periodically inspect each stand. Ensure all parts move
freely. Do not apply oil or grease to any portion of this
product. If rust appears, sand affected area and cover
with suitable utility paint.
Storage
Store stands in upright position and in a clean, dry
area.
REPLACEMENT PARTS
For product labels and owners manual, call or write:
SFA Companies 10939 N. Pomona Ave. Kansas City,
MO 64153, U.S.A. E-Mail: [email protected]
Tel: (888) 332-6419 Fax: (816) 891-6599
Website: http://www.omegalift.com
No other parts are available for this product. Jack stands
must
be replaced as a matched set and must never be
used singly or with another make or model stand.
• Study, understand, and follow all instructions
provided with and on this device
before use
.
•
Rated capacity is PER PAIR! DO NOT
exceed
rated capacity.
• Use as a matched pair to support one end of a
vehicle only. Use only
ONE (1) PAIR
per vehicle.
• Use only on hard, level surface.
• Center load on saddle.
• Jack stands are not to be used to simultaneously
support both ends or one side of a vehicle.
• No alterations shall be made to this device.
• Failure to heed these markings may result in
personal injury and/or property damage.
!
WARNING
!
!
!
