background image

 

 

 
 

Congratulations for your choice of a new vehicle security and convenience

system by Omega Research and Development.  You will find that your new system
will give you years of trouble-free convenience and protection.  To enjoy the most
from your new system, please take a few moments to learn about the principal user
components, and the basic operation of the system.  These subjects are found in next
several pages, followed by more detailed specifics of complete operations and
features.

Introduction to the System

disarm/unlock

Pressing and releasing the “

disarm/unlock

” button disarms the system and

unlocks the doors unless the alarm is triggered, in which case it will disarm the
activated alarm, but not unlock the doors unless the button is pressed again.

Pressing and holding this button for three seconds will first disarm, and then
activate the Panic feature, unlocking the doors.

The unlock operation may be optionally configured during the system’s
installation so that pressing this button once disarms the system and unlocks
only the driver's door, and pressing a second time unlocks all of the doors.

The

 Transmitter

The 

Transmitter

 operates the system.  It  has four buttons, and a small green

light between the two large buttons, which illuminates whenever a button is pressed
to transmit a command.

III

” button

II

” button

disarm/unlock

button

arm/lock

     button

arm/lock

Pressing and releasing  the “

arm/lock

” button arms the security system and

locks the doors.

Pressing and holding this button for three seconds will first arm, and then
activate the Panic feature, locking the doors.

Summary of Contents for K9 Classic-EDP2
















Reviews: