background image

Complete Programmable Features Matrix

Features

           Ignition on, off, then press Valet Switch 

5

 times  (Status Light turns on steady).

   #  Feature

Default Setting          Option

   2nd Option

  3rd Option

   1 SecureCode

 1 & 0                     

  2 stages, of up to 9 presses each (total of 99 possible combinations)

   2 Last Door Arming

OFF (L)

ON w/o doorlock (U)   ON w/ doorlock (2)

   3 Automatic Rearming

OFF (L)

ON w/o doorlock (U)   ON w/ doorlock (2)

   4 Starter Interrupt Functions

Alarm only (L)

Off (U)

Automatic (2)

   5 Ignition Activated Override

OFF (U)

ON (L)

   6 Doors Lock With Ignition On

ON  (L)

OFF (U)

   7 Doors Unlock With Ignition Off ON  (3)

OFF (L)

o/p 1 only (U)

o/p 2 only (2)

   8 Open Door Bypass to above

ON  (L)

OFF (U)

   9 Confirmation Chirps

ON (L)

OFF (U)

exc. Valet (2)

Valet only (3)

 10 Confirmation Chirp Volume

Medium Loud  (2) Low (L)

Med Lo (U)

Loud (3)

 11 Activated Alarm Cycle

 30 Seconds (L) 60 Sec. (U)

90 Sec. (2)

120 Sec. (3)

 12 Lights On Upon Disarm

ON  (L)

OFF (U)

 13 Disarm Upon Trunk Release

ON  (L)

OFF (U)

 14 Arming Delay

3 Seconds (L)

15 Seconds (U)

30 Seconds (2)

45 Seconds (3)

 15 Steady Siren / Pulsed Horn

Steady Siren (L) Pulsed Horn Lo (U)

Pulsed Med. (2)

Pulsed Hi (3)

 16 Alarm Functions Bypass

OFF (U)

ON (L)

 17 Ignition Anti-Carjacking

OFF (U)

ON (L)

 18 Door Anti-Carjacking

OFF (U)

ON (L)

 19 Remote Anti-Carjacking

OFF (U)

ON (L)

 20 Open Door Warning at Arm

OFF (U)

ON (L)

 21 III Button Operation

3rd Chan. (L) Panic  (U)

4th Chan. (2)

5th Chan. (3)

 22 Doorlock Functions        .8 second (L)

3 Seconds (U)   Double Unlock(2) Total Closure (3)

 23 (-) Parking Light Output        Parking Light (U)   Arm (L)

              Chan. 4 Latch (2) Chan. 4 On Demand (3)

 24 (-) Horn Output

Horn, med (U)  Disarm (L)

Chan. 5 Latch (2)       Chan. 5 On Demand (3)

installation  features

K9

CLASSIC-

EDP2

  OPERATION  MANUAL

Summary of Contents for K9 Classic-EDP2
















Reviews: