Omega National EVO Manual Download Page 2

Parts List

(Continued)

18 each:

    

#8 x 0.625" Truss Head Phillips Screw

20 each:

    

#8 x 1.75" Flat Head Phillips Screw

 each:

    

#8 x 1.25" Washer Head Phillips Screw

16 each:

    

Dowel Screw

4 each:

    

#8 x 1.25" Flat Head Phillips Screw

Assembly Instructions

Assembly Instructions

Step 1:

   F

OR

 C

ABINETS

 

WITH

 F

ACE

 F

RAMES

:

The EVO Pull-Out Pantry unit will have to be cut to length to fit 

correctly into the cabinet that you will be mounting the unit into. 

To  determine  the  correct  length  the  upper  spacer  blocks  will 

have to be installed first to provide a reference surface to mea-

sure from. The assembled Spacer Blocks provided will fit most 

cabinets that have a 3” Face Rail positioned above the opening 

where the Pull-Out Pantry unit will be mounted. If the cabinet has 

a narrower upper Face Rail, the assembled Spacer Blocks can 

be disassembled and fewer spacers can be used to work with 
other sizes of Face Frame Rails.

The  pre-assembled  Spacer  Blocks  should  work  without  the 

additional 3/8” Spacer when used with cabinetry with a 3” wide 

Face Rail, and as long as the upper shelf is either ½” or ¾” thick.  

However,  it  is  critical  that  you  verify  that  when  the  assembled 

Spacer  Blocks  are  positioned  under  the  top  shelf,  the  slide 

mounting surface is no more than 1/16 above the bottom edge of 

the 3” Face Rail, or does not extend down past the bottom edge 

of the 3” Face Rail for more than ¾”.

Please note that the EVO Pull-Out Pantry unit can be installed in either a Face Frame cabinet 

design that utilizes standard ¾” thick face frames (rails and stiles), or it can be installed in Fra-

meless Cabinets.

The following installation instructions are only for both cabinet designs.  Frameless style cabi-

nets will not require the Spacer Blocks as the Ball Bearing Slide will attach directly to the bot-

tom of the upper shelf. If you are installing the unit in a Frameless style cabinet, skip Steps 1 

and start with section 2. 

View is from inside of Cabinet

(

Shown without Slide for Clarity)

1/16" or 

less

Form OME-074, 01/2009

©Omega National Products

©Omega National Products

View is from inside of Cabinet

(

Shown without Slide for Clarity)

Summary of Contents for EVO








Reviews: