background image

25

EN

MAINTENANCE

•  Correct maintenance is crucial to achieve maximum efficiency of your compressor, and to lengthen its operating life.  

•  It is also important to comply with the maintenance intervals recommended, but it must be remembered that such intervals 

are suggested by the manufacturer in the event that the environmental conditions of use of the compressor are optimal (see 

“Installation” chapter).   

•  The maintenance intervals can therefore be reduced depending on the environmental conditions in which the compressor 

operates. 

•  The oil used is FSN Original Oil, the use of a different oil does not guarantee perfect efficiency and compliance with the 

maintenance intervals. 

•  The maintenance operations described in the table below and on the following pages must be carried out by authorised 

staff.

Maintenance table

To verify correct machine operation, perform the followng checks 

after the first 100 hours of work

:

1) Check the oil level

: top up with the same type of oil if necessary. 

2) Check for proper screw tightening

:

 

in particular the power electric connection screws. 

3) 

Visually check that all 

fittings seal properly. 

4) 

Check the

 hours of work 

and the 

type of service selected

5)

 Check

 room temperature

BEFORE MAINTAINING THE MACHINE ALWAYS PERFORM THE FOLLOWING:

 

Press the machine automatic stop button

 (do not use the emergency button).

 

Power the machine off by means of the wall outer switch.

 

Close the line cock.

 

Make sure that no compressed air is inside the oil separator tank.

 

Remove fairing and/ or panels. 

Type of maintenance

Maintenance schedule

work hours

o at least

(when MINERAL 

OIL is used)

(when SYNTHETIC 

OIL is used)

Drain condensate from air tank (if present)

50

50

weekly

Drain condensate from the oil tank

50

50

weekly

Clean cabinet pre-filter panel

50

50

weekly

Oil check and top up

500

500

once per month

Clean intake air filter cartridge 

500

500

-

Check and clean radiator

1000

1000

once a year

Replace primary intake air filter cartridge

2000

2000

once a year

Replace secondary intake air filter cartridge 

4000

4000

once a year

Replace oil filter 

2000

4000

once a year

Replace oil separator filter

2000

4000

once a year

Replace oil

2000

4000

once a year

Replace scavenge non return valve

4000

4000

once a year

Replace cabinet pre-filter

4000

4000

once a year

Condensate drainage filter cleaning

4000

4000

once a year

Intake valve service

8000

8000

Minimum pressure valve overhaul

8000

8000

Thermostatic valve service

8000

8000

Replace joint flexible

8000

8000

Replacing solenoid valves *

8000

8000

Replace flexible hoses

8000

8000

Air-end overhaul/ replacement

24000

24000

Refer to the motor manual and/or to the motor data plate for electric motor bearing maintenance.

* The second solenoid valve is on the condensation separator (for models fitted with it).

NOBEL DV 30-37 CSA - Cod.197EE0612ML - Rev.2 09/2019

Summary of Contents for NOBEL 30 DV CSA




























Reviews: