Omcan JBC-50 Instruction Manual Download Page 4

4

Installation / Operation

Safety

TEMPERATURE CONTROLS

The temperature controls are factory-set to maintain an average temperature of 38°F in refrigeration. To 

maintain a different temperature, simply adjust the control knob located inside the unit. To decrease the 

temperature (colder), turn clockwise. To increase the temperature(warmer), turn counter-clockwise – see 

diagram.

LOADING PRODUCT

The bin dividers have been installed at the factory for your convenience. Feel free to reposition the dividers 

as you see fit. To remove the bin dividers, simply push the divider towards the back wall unit the front of the 

divider is removed from the positioning holes. To install, position the divider to the desired holes, making sure 

that the pressure spring is installed properly.

PAY CLOSE ATTENTION TO THE LOAD LIMIT STICKERS LOCATED ON THE INTERIOR WALLS TO THE 

UNIT. DO NOT LOAD PRODUCT ABOVE THE LOAD LIMIT STICKERS OR ABOVE THE TOP CROSS BAR 

OF THE BIN DIVIDERS. LOADING PRODUCT ABOVE THE LOAD LIMIT STICKERS WILL HARM THE 

PERFORMANCE OF THE UNIT.

CAUTION

Setting the temperature control to the coldest setting may cause the Evaporator coil to freeze and ice up. This 

will eventually result in a warmer Cabinet temperature.

Temperature range from 7 (coldest) to 1 

(warmest).

Do not load Product above the top crossbar. 

Doing so will harm the Refrigeration.

Please pay close attention to the safety notices in this section. Disregarding these notices may lead to 

serious injury and/or damage to the unit.

ATTENTION

•  To minimize shock and fire hazards, be sure not to overload outlet. Please designate one outlet for your 

Summary of Contents for JBC-50

























Reviews: