background image

9

Troubleshooting

Condensing unit runs for long 

periods of time.

Excessive amount of warm product 

placed in cabinet.

Allow adequate time for product to 

cool down.

Prolonged door opening or door 

ajar.

Ensure doors are closed when not 

in use. Avoid opening doors for 

long periods of time.

Door gasket(s) not sealing 

properly.

Ensure gaskets are snapped in 

completely. Remove gasket and 

wash with soap and water.
Check condition of gasket and 

replace if necessary.

Dirty condenser coil.

Clean the condenser coil.

Evaporator coil iced over.

Unplug unit and allow coil to 

defrost. Make sure thermostat is 

not set too cold. Ensure that door 

gasket(s) are sealing properly.

Cabinet temperature is too warm.

Thermostat set too warm.

Set thermostat to lower 

Temperature.

Blocking air flow.

Re-arrange product to allow for 

proper air flow. Make sure there is 

at least four inches of clearance 

from evaporator.

Excessive amount of warm product 

placed in cabinet.

Allow adequate time for product to 

cool down.

Fuse blown or circuit breaker 

tripped.

Replace fuse or reset circuit 

breaker.

Dirty condenser coil.

Clean the condenser coil.

Prolonged door opening or door 

ajar.

Ensure doors are closed when not 

in use. Avoid opening doors for 

long periods of time.

Evaporator coil iced over.

Unplug unit and allow coil to 

defrost. Make sure thermostat is 

not set too cold. Ensure that door 

gasket(s) are sealing properly.

Cabinet is noisy.

Loose part(s).

Locate and tighten loose part(s).

Tubing vibration.

Ensure tubing is free from contact 

with other tubing or components.

Summary of Contents for FR-CN-0660-PC

























Reviews: