background image

17

Parts Breakdown

Model MG-ES-0022 

46204

Item No. Description

Position

Item No. Description

Position

Item No. Description

Position

AJ065

Feed Pan (Table) for 46204

W-501

AJ070

Throat Locking Knob for 46204

W-515

AJ077

Worm Shaft Brushing Gasket for 46204

W-535

36244

U Edge Green (Feed Pan Access Panel) 

for 46204

W-505

AJ071

Mincing Throat for 46204

W-516

66898

O-Ring Int. Diam. 61x2 for 46204

W-537

AJ066

Cabinet (Table) for 46204

W-506

AJ072

Worm for 46204

W-517

AJ078

Meat Feed Stomper for 46204

W-541

36177

Switch 3-Phase with Disconnector 16A 

208/220V 60Hz 11/01 for 46204

W-507

AJ073

Plates and Knives Shaft for 46204

W-518

AJ079

Gear Box Support Bar for 46204

W-547

AJ067

Block Fixing Screw for 46204

W-509

AJ074

Single Cutting Knife for 46204

W-519

AJ080

Knob Locking Stainless Steel Shaft 

for 46204

W-556

AJ068

Anti-Vibrating Support for 46204

W-510

AJ075

Fixing Plates Nut for 46204

W-525

39059

Air Extraction Fan 220V 1ph for 46204

W-564

AJ069

Counterweight for 46204

W-512

AJ076

Worm Extracting Wrench for 46204

W-526

AJ081

Box of Spare Knife Blades for 46204

W-565

Summary of Contents for 46204





















Reviews: