omal automation Rackon RK10 Instruction Manual Download Page 4

Page: 4 / 31

EN -

OMAL S.p.A.

Headquarters

: Via Ponte Nuovo, 11 - 25050 Rodengo Saiano (BS) Italy •

Production Site:

Via Brognolo, 12 - 25050 Passirano (BS) Italy

Ph.

+39 030 8900145 •

Fax

+39 030 8900423 • [email protected] •

www.omal.com

Reference 8_1522 - UMAAPRK0 - 07/20

INSTRUCTION MANUAL

RACKON: RACK & PINION PART TURN PNEUMATIC ACTUATOR

RK10 - RK480

2.4 Operating temperature

Standard working temperature range from –20°C (-4°F) to 80°C (176°F).

Actuators for Low or High temperature applications are available, please contact us.

Supplementary protection (e.g. screens, sheds, or integral painting) are strictly recommended for high humidity and low temperature

application.

2.5 Operating drive rotation

Part turn actuator rotation angle is nominally 90° with a ± 5° adjusting stroke: closing setting from -5° to +5° and opening setting from

85° to 95°.

2.6 Cycle time

Cycle time depends on different operational and installation factors such as supply pressure, flow capacity, pipe size connection,

solenoid valve performance, valve torque and characteristics, ambient temperature condition.

Double

Acting

0°- 90°

cycle time

(ms)

90°- 0°

cycle time

(ms)

RK10

RK20

RK40

131

110

RK60

160

120

RK80

189

130

RK120

137

125

RK160

183

177

RK240

304

288

RK300

383

354

RK480

522

455

Ambient temperature

18÷25°C (64,4÷77°F)

Supply pressure

compressed air; 5,5 bar (80 psi) for double acting and 6 bar (87psi) for spring return

Operating drive rotation

90° in both directions

Load

free

Spring Return

0°- 90°

cycle time

(ms)

90°- 0°

cycle time

(ms)

RK20

RK40

155

170

RK60

188

178

RK80

221

187

RK120

220

207

RK160

273

236

RK240

330

342

RK300

559

509

RK480

697

772

Actuator opening, closing and open/close cycle times

Above timetable refers to a standard actuator working cycle at the following tests conditions:

DA actuators operate with solenoid valves 5/2 ISO 1-2, while SR actuators operate with solenoid valves 3/2. Time tested by Electronic

Timer device.

Note

: different working conditions such as air pressure, piping connection, filters, or solenoid valves, could change operations timing.

Summary of Contents for Rackon RK10
































Search results

Summary of Contents for Rackon RK10

Reviews:

Brands by name

Popular brands

omal automation Rackon RK10, Instruction Manual

Search results

Summary of Contents for Rackon RK10

Reviews:

Brands by name

Popular brands