manualshive.com logo in svg

omal automation Rackon RK10, Instruction Manual

Share
Download
omal automation Rackon RK10 Instruction Manual Download Page 23

EN - 

23

OMAL S.p.A.

Headquarters

: Via Ponte Nuovo, 11 - 25050 Rodengo Saiano (BS) Italy  •  

Production Site:

 Via Brognolo, 12 - 25050 Passirano (BS) Italy

Ph.

 +39 030 8900145  •  

Fax

 +39 030 8900423  •  [email protected]  •  

www.omal.com

Reference 8_1522 - UMAAPRK0 - 07/20

IT

EN

DE

FR

ES

INSTRUCTION MANUAL

RACKON: RACK & PINION PART TURN PNEUMATIC ACTUATOR

RK10 - RK480

F. 

Remove Seeger (10) using expanding pliers.

 

G. 

Separate washer (9) from external support ring (8) from cylinder using a flat bladed screwdriver.

H. 

Pull down shaft (2) as shown in below picture. During this process hold cam (6) and internal support ring (7). Cam fall could 

cause irreversible scrapes or grooves in cylinder inner surface.

I. 

Pull up O-ring (12) and slide ring (3) and remove them.

J. 

Pull down O-ring (5) and slide ring (4) and remove them.

k. 

Do not use sharped tools to replace the components because they could generate irreversible scrapes or grooves on the shaft.

10

9

8

1

7

6

2

12

3

2

4

5

Summary of Contents for Rackon RK10
































Reviews:

No comments

Brands by name

Popular brands

Load more brands